24 to 36 W 3/4 19 mm 48 to 84 W 1 25.4 mm

Recommended minimum gas supply lines are listed below for Broilers:

24” to 36” W: 3/4” (19 mm)

48” to 84” W: 1" (25.4 mm)

When making gas pipe connections, only pipe joint compound resistant to the action of liquefied petroleum gases should be used.

The broiler and its individual shut-off valve must be disconnected from the gas supply system during any pressure testing of that system at test pressure in excess of ½ psig (3.45 kpa).

The broiler must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psig (3.45 kpa).

4. BURNERS:

Air-Mixer caps on the front of all burners are adjusted and tightened before the unit leaves the factory. If it is necessary to adjust the Air-Mixer caps, the adjustment must be done by a factory authorized technician only, who should tighten the adjustment screw after the adjustment. (See Figure “E”)

(i)Place the front venturi end of the burner onto valve assembly by fitting the center hole of the Air- Mixer cap over the brass orifice accessible through holes in the Chamber Front.

(ii)Drop the rear end flange of the burner into the corresponding slot in the burner support at the rear of the chamber.

(iii)While most of the Burners are H-shaped Double Burners, the 24”, 48” and 72” models come with one additional single Burner each. Place all of the H-shaped Burners first, then insert the single burner into the remaining space. (See Figure “D”)

5. RADIANT UNITS:

(i)If the Broiler was ordered with Grease Catches, place them with the slotted front end over the upturned fingers of the radiant support in front and rest the back end on top of the upturned fingers in the rear. (See Figure “D”)

(ii)Place the 'A' shaped radiants over the burners with each end supported on the radiant supports in front and rear of the chamber. Pushing the radiants all the way to the back will provide more heat in the front, while pushing them all the way to the front will provide more heat in the back.

(iii)Place the Top Grates, wider flange toward the back, onto the top grate supports in the rear. Every broiler is supplied with a sufficient number of Top Grates to cover the entire broiling area. Two of them are 4-1/2” wide and the rest are 6” wide. Flipping these Top Grates upside down and choosing between two supports in the rear, four positions are possible for different slopes desired.

6.GLO-STONE UNITS:

(i)Hold the Glo-Stone Frame (one or more, depending on the size of the Broiler) over the desired location and lower it slowly onto the Radiant Supports in the front and back of the chamber until it fits in between the upturned fingers of the supports. Rock it back and forth to assure proper fit.

(ii)Spread one layer of Glo-Stones covering all of the expanded metal grate exposed.

IMPORTANT NOTE: DO NOT USE MORE THAN ONE LAYER OF GLO-STONES, AS THIS WILL REDUCE THE AMOUNT OF HEAT REACHING THE TOP GRATES AND CAN CAUSE OVERHEATING AND PERMANENT DAMAGE TO THE UNIT.

F, L, C specifications

Bakers Pride Oven F, L, C stands as a hallmark of quality and reliability in the commercial baking industry. Known for its exceptional performance and innovative features, this oven is designed to meet the needs of various baking operations, from artisanal bakeries to large-scale production facilities. With a strong emphasis on efficiency and durability, it has become a beloved choice for professional bakers worldwide.

One of the standout features of the Bakers Pride Oven F, L, C is its robust construction. The oven is built with high-quality stainless steel, ensuring it can withstand the rigors of daily use while maintaining an attractive appearance. The heavy-duty materials used in its construction contribute to its longevity and ability to deliver consistent results over time.

The oven's advanced heating technology is another key characteristic that sets it apart. It utilizes a combination of electric heating elements and high-performance insulation to create an even and controllable baking environment. This technology not only ensures precise temperature management but also promotes energy efficiency, significantly reducing operational costs for baking establishments.

Moreover, the Bakers Pride Oven boasts a user-friendly digital control panel that allows bakers to easily monitor and adjust temperatures, baking times, and settings. This intuitive interface enhances the overall baking experience, enabling users to achieve their desired results with minimal effort. The programmable options also cater to the diverse needs of various recipes and baking styles.

In terms of versatility, the Bakers Pride Oven F, L, C excels with its adjustable racks and multi-functional design. It can accommodate a wide range of baking products, from pizzas and bread to pastries and cookies. This flexibility is crucial for businesses that require an oven capable of handling diverse menu offerings without compromising on quality.

Furthermore, the oven's exceptional airflow system ensures optimal heat distribution, allowing for uniform baking and browning of baked goods. This feature is vital for achieving professional-grade results consistently, making it an indispensable tool for any serious baker.

To sum up, the Bakers Pride Oven F, L, C is a reliable and feature-rich choice for commercial baking needs. With its durable construction, advanced heating and control technologies, and exceptional versatility, it stands out as a leader in the industry, helping bakers create delicious products that keep customers coming back for more.