Therma-Stor Products Group Quiet-Vent Ventilation System owner manual Specifications, Installation

Table of Contents
1	Specifications		1
2	Installation		1
	2.1	Back-Drafting Open Combustion Devices	2
	2.2	Location of the Quiet-Vent	2
	2.3	Fresh Air Inlets	3
	2.4	Hanging the Quiet-Vent	4
	2.5	Ducting to and from the Quiet-Vent	4
	2.6	Wiring the Quiet-Vent	4
3	Operation		5
	3.1	Using the Timers	5
	3.2	Adjusting the Amount of Ventilation	5
4	Maintenance		5
	4.1	Lubricating the Blower Motor	5
	4.2	Cleaning the Blower Screen	5
5	Service		6
	5.1	Circuit Breaker Trips	6
	5.2	Blower Operates on One Speed Only	6
	5.3	7-Day Timer Does Not Advance	6
	5.4	Fan Motor	6
	5.5	Warranty	6
6	Service Parts List		6
7.	Warranty		7

Serial No.____________________________________

Purchase Date________________________________

Dealer’s Name _______________________________

1 Specifications

Model: Quiet-Vent

Electrical Specs: 110-120Vac, 60Hz, 1ph

Max HACR Type Circuit Breaker or Fuse: 10A

Blower: Fasco 7090-1806 0.65 Amps, Thermally Protected

Capacitor: 370 VAC, 6 MFD

2 Installation

WARNING: To reduce the risk of fire, electric shock, or injury to persons, observe the following:

A.Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

B.Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

C.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

D.Ducted fans must always be vented to the outdoors.

E.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

F.NEVER place a switch where it can be reached from a tub or shower.

Read the operation and maintenance instructions carefully before using this unit. Proper adherence to these instructions is essential to obtain maximum benefit from your Quiet-Vent Ventilation system.

2.1 Back-Drafting Open Combustion Devices

CAUTION: Do not use open combustion heating appliances (unless equipped with power exhaust) in a home equipped with exhaust fans (i.e., bath fans, kitchen hoods, down draft stoves, or the Quiet- Vent System).

Under certain conditions, these fans may cause the backdrafting of toxic combustion by-products that are hazardous to human health and could cause death. Therefore, we strongly recommend using only closedcombustion (direct-vent or aerodynamically decoupled) heating appliances in weather tight homes. Most fur- naces, fireplaces and water heaters are now available with sealed combustion or power exhaust.

2.2 Location of the Quiet-Vent

Ideally each bathroom and the kitchen are ducted with a 4” duct to the Quiet-Vent (See Fig. 3). To make installation easy, the Quiet-Vent has one 6” and three 4” duct inlet Connections (see Fig. 2). The 6” outlet of the Quiet-Vent is ducted to the outside of the home. The Quiet-Vent should

Toll-Free 1-800-533-7533  www.thermastor.com • sales@thermastor.com