Installation in Existing Construction

INSTALLATION IN A NEW CONSTRUCTION SITE (continued)

3.Snap duct adapter over flanges on housing. Run 3" round duct from housing to wall or roof cap.

Refer to Figures Figures 1 and 2.

IMPORTANT: Be sure nothing obstructs the discharge of the fan. Take precautions to assure that insulation does not get into ductwork or fan discharge opening.

4.Refer to Figure 3. Run 120vAC, 60Hz power wiring from wall switch to ventilator housing. Remove the housing junction box cover and connect wires from wall switch to receptacle wires, using wire connectors - white to white, black to black. Use a box connector on junction box. Connect earth ground to green screw in junction box. Replace junction box cover.

CAUTION: Be sure all wiring complies with local electrical codes and housing is properly grounded.

5.Refer to Figure 4. Insert blower unit into housing, with stud on mounting bracket on the side near the receptacle. Turn bracket clockwise to lock blower into position, then tighten the three screws. Plug in motor.

6.MODEL 8832NA: Compress spring clips on grille and isert into slots provided in housing. Push grille up flush to ceiling. MODEL 8833NA: Place hole in center of grille bezel over stud on motor plate and fasten with nut provided. Snap grille panel over the four (4) spring clips on grille bezel.

To install the ventilator in an existing home requires accessible area above the proposed installation location (attic

BLOWER

MOUNTING

STUD

MOUNTING	FIGURE 4
SCREWS (3)

or crawl space). Because of the size and shape of the ventilator housing it must be installed to a finished ceiling from above.

Installation Hints

1.Review the section: INSTALLATION IN NEW CONSTRUCTION SITE and follow all instructions where applicable for your installation.

2.Refer to Figures 1 and 2 for duct work and Figure 3 for wiring.

3.Drill small hole in ceiling in proposed location, then locate this hole in attic or crawl space).

4.In attic, position housing over drilled hole and against ceiling joist, being sure to have duct collar in the direction of the ductwork. Mark ceiling for cutout by using housing as a template - mark along the plaster flange. make cutout on this outline.

5.Connect wires to receptacle wires in housing before mounting.

6.Mount housing to ceiling joist.

One Year Limited Warranty

WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.

WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

Date of Installation	Builder or Installer

Model No. and Product Description
	IF YOU NEED ASSISTANCE OR SERVICE:
	For the location of your nearest NuTone Independent Authorized Service Center:
	Residents of the contiguous United States Dial Free 1-800-543-8687
	Please be prepared to provide:
	Product model number • Date and Proof of purchase • The nature of the difficulty

Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.

Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.

Rev. 03/2001

Product specifications subject to change without notice.	4820 Red Bank Road, Cincinnati, Ohio 45227
	Printed in U.S.A., Rev. 01/2004, Part No. 84762

8832WH, 8832SA, 8833 specifications

NuTone, a leader in quality household products, offers a variety of ventilation solutions tailored to meet diverse needs. Among their notable offerings are the NuTone 8832SA, 8833, and 8832WH. These models are designed for efficient air circulation, enhancing indoor air quality while blending into modern home designs.

The NuTone 8832SA, part of the company's commitment to performance and style, features a powerful motor capable of delivering airflow at an impressive rate, making it ideal for use in bathrooms or smaller spaces that require effective ventilation. Its sleek design is complemented by durable construction, ensuring longevity and reliability. The 8832SA also includes an adjustable humidity sensor, which activates the fan automatically when moisture levels rise, thus preventing mold and mildew growth.

Moving on to the NuTone 8833, this model brings additional features to the table. It includes a built-in light that illuminates the space while the fan is in operation, providing both functionality and aesthetic value. The energy-efficient motor operates quietly, reducing noise disturbance while enhancing air circulation. Moreover, the 8833 is equipped with a convenient wall switch that provides easy control over fan and light settings, making it a versatile choice for areas where both ventilation and illumination are needed.

Lastly, the NuTone 8832WH showcases similar core features, but with a focus on a streamlined design that appeals to contemporary tastes. The white finish allows it to blend seamlessly with various decor styles, making it an excellent addition to any room. Like its counterparts, it operates quietly and effectively, ensuring a comfortable environment free from excess humidity and odors.

All three models highlight NuTone's commitment to incorporating advanced technologies into their products. They are designed to be user-friendly while promoting energy conservation. The emphasis on quiet operation makes them perfect for sensitive environments, particularly in homes where peace and tranquility are paramount.

In summary, the NuTone 8832SA, 8833, and 8832WH represent a trifecta of high-quality ventilation solutions, each with its unique features catering to different user needs. From automatic humidity sensing to integrated lighting options, these models are indispensable for maintaining a healthy and comfortable living space. Whether for a bathroom, kitchen, or laundry room, NuTone continues to prove its expertise in home ventilation, ensuring every household enjoys improved air quality with style and efficiency.

INSTALLATION IN A NEW CONSTRUCTION SITE (continued)