Kobe Range Hoods CX1842GS-8 manual Sure the Hood is Secure Before Releasing

Page 8

4.Place rubber seal on hood venting area; make sure the openings on rubber seal are aligned with openings in vent area. Shown in Figure 7. Align plastic damper on rubber seal and attach to hood using eight 4x20 mm screws (provided). Refer to Figure 8

Figure7	Figure 8
5.If necessary, remove the two rubber stands at the back of the
hood. For a more secure installation, KOBE recommends not
removing the rubber stands.
6.Using references in Table 1 and Measurement & Diagrams on
page 14, mark the leveling line for hood-mounting bracket.
Secure hood-mounting bracket to wall with screws (not provided).
Refer to Figure 9.
7.Align hood to the hood-mounting bracket on the wall and hook		Figure 9
hood into place as shown in Figure 10 & 11. CAUTION: MAKE
SURE THE HOOD IS SECURE BEFORE RELEASING.

Figure 10

Figure 11

8.For safety purposes, install the safety bracket (provided) with one screw (not provided) to the wall as shown in Figure 12.

Figure 12

6

Image 8

Contents Kobe Brand Range Hood Read and Save These Instructions N T E N T SImportant Safety Instructions Grease FirePage Components of Package Box 2Installation Please Read Entire Instructions Before ProceedingShut OFF the GAS Before Moving a GAS Range Sure the Hood is Secure Before Releasing Wiring to Power Supply Page Operating Instruction Page Maintenance Paper Towel on Stainless SteelTo Clean Carbon Filter Optional Recirculating Kit Specifications Exhaust Controls Halogen LightsSpeed AIR Capacity CFM Sone NETMeasurements & Diagrams Part List Model NO. CX1830GS-8Recirculating KIT Optional Model No. RD-0183 Circuit Diagram Model noTrouble Shooting Issue Possible Cause SolutionDisclaimer Claims will not be Accepted After the Allocated DaysWarranty Warranty CertificateTWO-YEAR Warranty Service Period ConditionsImplied WARRANTIES/STATE LAW ServiceConsequential Damage Product Registration Record the Following Information for Your RecordInformation subject to change without notice VER.091208 Hotte DE Cuisinière Kobe Lire ET Conserver CES Instructions SVP Lire Cette Section Attentivement Avant Linstallation Consignes DE Sécurité ImportantesAvertissement Contenu DE Lemballage Boîte 2 deSVP Lire AU Complet Avant Linstallation TableauPhoto Page Consigne DE Sécurité Page Mode Demploi Page Avertissement Entretien PréventifRemplacement des ampoules de lampe à halogène Spécifications Mesures ET Schémas Liste DES Pièces No de modèle CX1830GS-8, CX1836GS-8, CX1842GS-8No de modèle Schéma DE Câblage Problema Posible Causa Solución Instrucciones Importantes DE SeguridadCláusula DE Exención Condiciones Certificado DE GarantíaPeriodo DE Servicio DE LA Garantía DE DOS Años Servicio Daños EmergentesGarantías IMPLÍCITAS/LEY Estatal Enregistrement de votre produit Information subject to change without notice VER.091208 Campana de Extracción Kobe ÍN D IC E Instrucciones Importantes DE Seguridad Qué Hacer si Siente Olor a Gas AdvertenciaComponentes DEL Paquete Caja 2 deInstalación TablaMover UNA Estufa DE GAS Figura Advertencia DE Seguridad Figura Instrucciones DE Operación Page Mantenimiento Para Reemplazar el Foco Accessorios Opcionales EspecificacionesVelocidad Capacidad DE Aire CFM Sonio NetoMedidas Y Diagramas Listado DE Piezas Modelo noModelo NO. CX1830GS-8 Diagrama DE Circuito Modelo NO. CX1830GS-8 CX1836GS-8 CX1842GS-8Tighten the turbine impeller/squirrel cage Faltara Algún Material DE Empaque GARANTĺ a Daños Emergentes Registro DEL Producto Escriba LA Siguiente Información Para SUS ArchivosInformation subject to change without notice VER.091208