Kobe Range Hoods IS2442GSB Telescopic Stack Installation, Wiring to Power Supply, Safety Warning

Page 8

Telescopic Stack Installation

Telescopic Stack Installation

6.Align the telescopic stack to the pre-drill holes on the ceiling and securely fasten to the joists and cross framing lumber with eight screws (not provided). Make sure screws are driven into center of joists and cross framing lumber for maximum support.

7.Adjust the blower unit to the telescopic stack using reference F calculated in TABLE 1 on page 4 and measurements on pages 14-15. Tighten blower unit to the telescopic stack with four (M5 x 15) screws (provided) as shown in Figure 4.

Wiring to Power Supply

SAFETY WARNING

RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE

BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY.

8.Route house wiring into the ceiling as close to the installation location as possible. Allow additional length to drop down from the ceiling to the electric box.

9.Connect the electrical wires according to color (green to green, white to white, and green to green) and cap with wire connectors as shown in Figure 5. Green wire must be grounded to reduce risk of electric shock.

Figure 4

Figure 5

Figure 6

Ductwork Installation

10.Use 7” round aluminum or steel pipe (not provided) to connect the 7” round damper on the hood to the ductwork above. NOTE: Place 7” round duct pipe over the damper. Seal with duct tape to make all joints secure and air tight. NOTE: MAKE SURE FLAPS ON DAMPER CAN OPEN & CLOSE FREELY. (Figure 6)

6

Image 8

Contents “ISLAND GLASS CANOPY WITH LCD SCREEN” KOBE Brand Range HoodModel No. IS2436GSB IS2442GSB IS-124 SERIES CONTENTS ALL WIRING MUST BE DONE BY A PROFESSIONAL AND INREAD AND SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTINGIMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATIONWhat to Do In The Event Of a Range Top Grease Fire COMPONENTS OF PACKAGE BOX 1 OF MODEL NO. IS2436GSB MODEL NO. IS2442GSBBOX 2 OF MODEL NO. IS124DC Must keep all material for returns or refundsSAFETY WARNING INSTALLATIONC = Preferred Height of Counter Top to Hood Bottom Recommended 30” to 36”Important Peel protective film off the hood and duct covers, if any Preparation before InstallationAdvance Planning Ductwork Installation Telescopic Stack InstallationWiring to Power Supply Connection to LCD Screen Duct Cover InstallationFinal Assembly OPERATION INSTRUCTIONS LCD DISPLAYWhen appears, keypad sound is ON 1. Press until flashesSetting Delay Mode Setting Timer ModeTurning ISC Integrated Sensor Control ON/OFF Turning Lights ONMAINTENANCE To Clean Hood SurfaceCAUTION NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS To Clean or Replace Baffle FilterTo Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOLSPECIFICATIONS MEASUREMENTS & DIAGRAMS Sold SeparatelyPARTS LIST Box 1 ofMODEL NO. IS2436GSB MODEL NO. IS2442GSBMODEL NO. IS2436GSB IS2442GSB BOX 1 OF 2 - GLASS CANOPY WITH LCD SCREENBOX 2 OF 2 - DUCT COVER OPTIONALCIRCUIT DIAGRAM DISCLAIMER DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY2. PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIPT CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYSWARRANTY WARRANTY CERTIFICATETWO-YEAR WARRANTY SERVICE PERIOD CONDITIONSIMPLIED WARRANTIES/STATE LAW SERVICECONSEQUENTIAL DAMAGE RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD PRODUCT REGISTRATIONRegister Your Product KOBE Range Hoods 10505 Valley Blvd Suite # El Monte, CA 91731 USA