Kobe Range Hoods CH0130SQB (30") Under the Cabinet Installation, Preparation Before Installation

Page 9

UNDER THE CABINET INSTALLATION

Preparation Before Installation

NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING.

•Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1.

•A straight, short vent run will allow the hood to perform more efficiently.

•Try to avoid as many transitions, elbows, and long runs as possible. This may reduce the performance of the hood.

•Temporarily wire the hood to test for proper operation before installing.

•NOTE: Peel protective film off the hood and parts (if any).

•To install hood under a cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 2.

•Using references in Table 1 and Measurements and Diagrams on pages 17-18, create access opening for electrical wires and ducting transition under the cabinet.

Hood Installation

CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.

1.Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 3.

2.Attach ducting transition to hood exhaust with ten (3/16” x 3/8”) screws (provided). Shown in Figure 4.

3.Draw electrical wires through cabinet access opening.

4.Center the hood beneath the cabinet and flush with the front of the cabinet.

5.From the bottom of the hood, place mounting screw (not provided) through each knockout hole and secure to cabinet bottom. Once all mounting screws are in place, finish tightening screws until secure. CAUTION:

MAKE SURE HOOD IS SECURE BEFORE RELEASING.

6.For safety purpose, extra knockout holes on the back of the hood are provided for a more secure installation. Knock out as many holes as needed and secure with screws (not provided) from the inside of hood.

6

Figure 1

Figure 2

Figure 3

Figure 4

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Kobe Brand Range Hood Page Read and Save These Instructions ContentsPage Page Must keep all material for returns or refunds Components of PackageInstallation For Under the CabinetFor Stand Alone with Optional Duct Cover Installation Table of Contents Preparation Before Installation Under the Cabinet InstallationF E T Y W a R N I N G Page Hood Preparation Before Installation Stand Alone InstallationSafety Warning Duct Cover Installation Operating Instructions Speed Control To Clean Hood Surface MaintenanceHalogen Light Unit MAY be HOT! Wait Until Unit is Cool Specifications Measurements & Diagrams For Under the Cabinet Page For Stand Alone with Optional Duct Cover Baffle Filter & Stainless Steel Spacers Description MODEL/SIZE Parts ListOptional Duct Cover Sold Separately Blower Assembly Electrical Assembly Switch Assembly Circuit Diagram Model NO. CH0130SQB CH0136SQB Model NO. CH0142SQB CH0148SQB Claims will not be Accepted After the Allocated Days Warranty Warranty Certificate TWO-YEAR Warranty Service PeriodConditions Service Consequential DamageImplied WARRANTIES/STATE LAW Record the Following Information for Your Record Product Registration070530

CH0148SQB (48"), CH0142SQB (42"), CH0130SQB (30"), CH0136SQB (36") specifications

Kobe Range Hoods has established itself as a leading brand in kitchen ventilation systems, with products designed to enhance the cooking experience while marrying style and functionality. Among its impressive lineup are the CH0142SQB (42"), CH0136SQB (36"), CH0130SQB (30"), and CH0148SQB (48") range hoods, each tailored to meet the diverse needs of modern kitchens.

One of the standout features of the CH0142SQB, CH0136SQB, CH0130SQB, and CH0148SQB models is their powerful suction capabilities. Utilizing a powerful motor, each unit delivers exceptional airflow, effectively capturing smoke, steam, and odors generated during cooking. This ensures a clean and comfortable kitchen environment, promoting better air quality for the home.

In addition to robust performance, these range hoods come equipped with innovative technologies. The baffle filters are a key component, known for their durability and effectiveness. Made from stainless steel, these filters are not only easy to clean but also designed to maximize airflow while minimizing noise levels, creating a quieter cooking environment. Each model features a three-speed blower that allows users to select the appropriate level of ventilation based on cooking intensity. This versatility caters to a range of cooking styles, from everyday meal preparation to gourmet cooking sessions.

Aesthetically, the Kobe range hoods boast a sleek and modern design, making them a stylish addition to any kitchen. Available in various sizes—42", 36", 30", and 48"—they can fit seamlessly into diverse kitchen layouts and complement a wide range of cabinetry styles. The stainless steel finish gives each model a contemporary look while also providing durability and ease of maintenance.

Moreover, these range hoods are equipped with LED lighting, offering bright illumination of the cooking surface below. This enhances visibility while preparing meals, ensuring that users can maintain precision and safety during cooking.

In terms of installation, the Kobe Range Hoods are designed for easy setup, with options available for both ducted and ductless installations, making them adaptable to different home configurations. Each unit delivers a combination of efficiency, style, and user-friendliness, positioning them as an excellent choice for anyone looking to upgrade their kitchen ventilation solution.

Overall, the CH0142SQB, CH0136SQB, CH0130SQB, and CH0148SQB models exemplify Kobe Range Hoods' commitment to quality and innovation, making them a top choice for chefs and home cooks alike.
Top Page Image Contents