Zanussi ZCM 650 ZCM 651 manual Installation, Positioning the Appliance Fig

Page 31

Location of the appliance

This appliance must not be installed in a bed-sitting room of volume less than 20m³ or in a bathroom, shower room or garage. It is essential that the appliance is positioned as stated below (see fig.1) i.e. shelves, wall cabinets and cooker hoods must be fitted a minimum of 787mm directly above the top of the hotplate and 400mm above the hotplate when fitted in line with the outside of the appliance. If the units are intended to be fitted adjacent to the appliance but less than 400mm above the hotplate, then a minimum space of 100mm must be maintained between the sides of the unit and the appliance (see fig.). Curtains must not be fitted immediately behind the appliance or within 150mm of the sides of the hotplate. If fitted next to or between two base units a minimum space of 1mm must be left between each unit and the side of the appliance. The levelling feet fitted to the appliance will achieve a nominal height to hotplate trims of 900mm +20mm.

Installation

Positioning the Appliance (Fig. 1)

This appliance cannot be positioned on a base.

The appliance cannot be installed beside or between furniture units whose height exceeds the cooker worktop.

Note A:

The appliance is designed to be flush fitted with 2mm clearance at each side to allow for it to be pulled forward for cleaning etc.

Note B:

The hotplate side trims should be flush with the cabinets and must not be below. Adjustable levelling feet at the front and rear are provided on the base of the appliance. Adjustment is obtained by rotating in or out, the feet at the front or rear of the appliance from the underside of the appliance.

A spirit level should be placed on a cake tray on one of the shelves to confirm that the appliance is correctly levelled.

The levelling feet fitted to the appliance will achieve a height to hotplate trims of 900mm-0 + 10.

Note C:

If the appliance is fitted next to a side wall or cabinets above height of the hotplate trims, then a gap of 115 mm is required.

Curtains must not be fitted immediately behind the cooker or within 115 mm of the sides of the cooker.

Note D:

Any wall cabinet or extractor must not be lower than 780mm above hotplate level.

Note E:

Wall cabinets may be fitted in line with the sides of the base units, providing that the lower edge of the wall cabinet is a minimum of 420mm above the worktop.

L.P.G. cookers MUST NOT be installed below ground level, i.e. in a basement, or aboard any boat, yacht or other vessel.

For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance.

Positioning the Cooker

Caution:

Some soft or badly fitted floor coverings can be damaged when the cooker is moved across their surface for cleaning. It is advisable to ensure that the floor covering in the area below the cooker is either securely fixed so as not to become damaged when the cooker is moved or, if preferred, removed.

 

D

 

 

C

 

780

E

115

420

 

 

 

 

B

 

 

 

 

 

A

FO 1141

 

 

 

Fig. 1

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Mixed Fuel Cookers Page Important Safety Information Contents Control Panel AccessoriesOven Cavity Gas Hob Controls Oven Function Control Knob Time/Temperature Control knobSafety Thermostat Electric OvenOven will work only if the time of day has been set How to set the time of dayTo reset the correct time of day Electronic programmerSpecial functions Temperature level indicatorsBefore the First Use of the Cooker Using the ceramic hob for the first timeHeating up for the first time To set the minute minder To cancel the minute minderProgramming the Oven Minute minder functionTo change the duration time How to make the oven switch off automaticallyTo cancel the duration time To set the duration timeHow to make the oven switch on and off automatically How to switch off the display Safety and Energy saving functionsSafety Cut-Off Function Child Safety FunctionHints and Tips Using the OvenHints and Tips Using the Conventional OvenHow to Use Conventional Oven Top oven element onlyTemperature Cooking time Position Minutes Cooking Chart Conventional OvenPizza Oven Pizza OvenGrilling How to Use the Full GrillHow to Use the Inner Grill GrillingDefrosting Chart How to Use DefrostingDefrosting Burners Maintenance and CleaningHob Top Pan SupportsPyrolytic cleaning Cleaning the OvenCleaning materials External cleaningHow to use the pyrolytic clean- ing function Page Extract the inner glass support Cleaning The Oven DoorDisconnect the appliance from the electricity supply Oven lamp replacementSomething not working Symptom SolutionCustomer Care Department Service and Spare PartsCustomer Care Department 0870 5This guarantee does not cover Guarantee ConditionsZanussi-Electrolux Guarantee conditions Exclusions European GuaranteeImportant Safety Requirements Instructions for the InstallerPositioning the Appliance Fig InstallationThis appliance cannot be positioned on a base Fitting the Stability Bracket Not supplied Connecting to GasElectrical connections Supply Cable SpecificationsMin. size Cable/flex Conversion from Natural Gas to LPG ProcedureTo adjust the gas rate Commissioning79 kWh 78 kWh 43 min 41 min 1130 cm² Customer Care

ZCM 650 ZCM 651 specifications

Zanussi, a renowned name in kitchen appliances, offers a range of products that combine functionality, style, and energy efficiency. Among its notable offerings are the Zanussi ZCM 650 and ZCM 651, two modern gas cookers designed to enhance culinary experiences in the home.

The Zanussi ZCM 650 and ZCM 651 are designed with user-friendly features, making cooking a pleasurable and efficient task. Both models boast a sleek stainless-steel finish that not only elevates the aesthetics of any kitchen but also ensures durability and easy maintenance. The classic freestanding design allows for flexible placement within the kitchen, making them suitable for a variety of kitchen layouts.

One of the standout characteristics of these models is their powerful gas burners. The ZCM 650 features four burners, while the ZCM 651 offers a similar configuration but with additional enhancements. These burners provide excellent heat distribution, allowing users to achieve the perfect temperature for different cooking techniques, whether it's quick boiling, simmering, or frying. In addition to this, the high-efficiency burners ensure that cooking is both faster and more energy-efficient.

Safety is a key component in the design of the Zanussi ZCM series. Both the ZCM 650 and ZCM 651 come with an integrated flame failure safety device. This technology automatically cuts off the gas supply if the flame is accidentally extinguished, providing peace of mind during cooking.

The ovens in the ZCM 650 and ZCM 651 models are designed with a fan-assisted cooking system that ensures even heating throughout the oven cavity. This technology not only reduces cooking time but also allows for multiple dishes to be prepared simultaneously without flavor transfer. The large capacity of the oven makes it perfect for families or those who love to entertain guests.

Moreover, these cookers feature easy-to-use controls, allowing users to adjust temperatures and settings effortlessly. The easy-clean enamel interior ensures that maintaining the cleanliness of the oven is a simple task, further enhancing the user experience.

In terms of energy efficiency, both the ZCM 650 and ZCM 651 are built to meet modern standards, helping to reduce energy consumption while providing powerful cooking performance.

Overall, the Zanussi ZCM 650 and ZCM 651 gas cookers deliver a blend of style, safety, and high performance, making them ideal options for any home chef looking to elevate their cooking experience.
Top Page Image Contents