Zanussi ZCM 650 ZCM 651 manual Fitting the Stability Bracket Not supplied, Connecting to Gas

Page 32

 

 

300 mm.

 

 

WALL FACE

 

 

 

 

 

 

 

BACK OF COOKER

580 mm.

mm.

 

 

ENGAGEMENT EDGE FOR

LEVELLING FEET

 

STABILITY BRACKET

 

100

 

 

 

 

 

 

 

 

A

BASE OF COOKER

 

 

 

 

 

PENCIL LINE ON THE FLOOR

 

 

 

 

 

295 mm.

 

 

 

PLAN VIEW OF THE COOKER

 

SIDE VIEW

FO 0179

 

OF THE COOKER

 

 

 

 

Fig. 2

Fitting the Stability Bracket (Not supplied)

If the cooker has to be installed with a flexible supply pipe, it is necessary that a stability device is fitted. (See "Important Safety Requirements").

The stability bracket should be fitted by the installer and these instructions should be read in conjunction with the leaflet packed with the stability bracket.

Place cooker in its intended position and level cooker.

Mark off 295mm (11 1/2") from the right hand side of the cooker as shown, this is the centre line of the bracket fixing.

Draw a line 100mm (4") from the front edge of the levelling feet (see Fig. 1) and remove cooker from its position. Mark off 580mm (23") back from this line on the centre line of the bracket to locate the front edge of the lower bracket.

Fix lower bracket (with two fixing holes) to the floor, then measure height from floor level to engagement edge on back of cooker, dimension 'A' of Fig. 2.

Assemble upper bracket to lower bracket so that underside of bracket is dimension 'A' +3mm (1/8") above floor level. Re-position cooker and check that top bracket engages into cooker back to a depth of 75mm (3"), as shown in Fig. 2.

Should the stability bracket currently installed not allow the cooker to stand correctly, ask the installer to replace it with the correct type.

Connecting to Gas

This cooker is designed to be installed with an appliance flexible connection. Connection is made to the RC 1/2 (1/2" B.S.P.) threaded entry pipe located just below the hotplate level on the rear right-hand side of the cooker. Check for gas soundness after connecting the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated in Fig. 3. Take into account that it must be possible to pull the cooker forward sufficiently. The hose must not get caught on the stability bracket.

Note:

If using different types of gas bayonet connection, it may not be possible for the appliance to be pushed fully back to the wall stops.

Important:

Flexible tubing MUST comply with BS.669 Current Edition.

600

 

 

450

 

130

FO 0180

Fig. 3

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Mixed Fuel Cookers Page Important Safety Information Contents Oven Cavity AccessoriesControl Panel Gas Hob Controls Time/Temperature Control knob Safety ThermostatElectric Oven Oven Function Control KnobHow to set the time of day To reset the correct time of dayElectronic programmer Oven will work only if the time of day has been setTemperature level indicators Special functionsHeating up for the first time Using the ceramic hob for the first timeBefore the First Use of the Cooker To cancel the minute minder Programming the OvenMinute minder function To set the minute minderHow to make the oven switch off automatically To cancel the duration timeTo set the duration time To change the duration timeHow to make the oven switch on and off automatically Safety and Energy saving functions Safety Cut-Off FunctionChild Safety Function How to switch off the displayUsing the Oven Hints and TipsUsing the Conventional Oven How to Use Conventional OvenTop oven element only Hints and TipsCooking Chart Conventional Oven Temperature Cooking time Position MinutesPizza Oven Pizza OvenHow to Use the Full Grill How to Use the Inner GrillGrilling GrillingDefrosting How to Use DefrostingDefrosting Chart Maintenance and Cleaning Hob TopPan Supports BurnersCleaning the Oven Cleaning materialsExternal cleaning Pyrolytic cleaningHow to use the pyrolytic clean- ing function Page Cleaning The Oven Door Extract the inner glass supportOven lamp replacement Disconnect the appliance from the electricity supplySymptom Solution Something not workingService and Spare Parts Customer Care Department0870 5 Customer Care DepartmentGuarantee Conditions Zanussi-Electrolux Guarantee conditionsExclusions European Guarantee This guarantee does not coverInstructions for the Installer Important Safety RequirementsThis appliance cannot be positioned on a base InstallationPositioning the Appliance Fig Connecting to Gas Fitting the Stability Bracket Not suppliedMin. size Cable/flex Supply Cable SpecificationsElectrical connections Procedure To adjust the gas rateCommissioning Conversion from Natural Gas to LPG79 kWh 78 kWh 43 min 41 min 1130 cm² Customer Care

ZCM 650 ZCM 651 specifications

Zanussi, a renowned name in kitchen appliances, offers a range of products that combine functionality, style, and energy efficiency. Among its notable offerings are the Zanussi ZCM 650 and ZCM 651, two modern gas cookers designed to enhance culinary experiences in the home.

The Zanussi ZCM 650 and ZCM 651 are designed with user-friendly features, making cooking a pleasurable and efficient task. Both models boast a sleek stainless-steel finish that not only elevates the aesthetics of any kitchen but also ensures durability and easy maintenance. The classic freestanding design allows for flexible placement within the kitchen, making them suitable for a variety of kitchen layouts.

One of the standout characteristics of these models is their powerful gas burners. The ZCM 650 features four burners, while the ZCM 651 offers a similar configuration but with additional enhancements. These burners provide excellent heat distribution, allowing users to achieve the perfect temperature for different cooking techniques, whether it's quick boiling, simmering, or frying. In addition to this, the high-efficiency burners ensure that cooking is both faster and more energy-efficient.

Safety is a key component in the design of the Zanussi ZCM series. Both the ZCM 650 and ZCM 651 come with an integrated flame failure safety device. This technology automatically cuts off the gas supply if the flame is accidentally extinguished, providing peace of mind during cooking.

The ovens in the ZCM 650 and ZCM 651 models are designed with a fan-assisted cooking system that ensures even heating throughout the oven cavity. This technology not only reduces cooking time but also allows for multiple dishes to be prepared simultaneously without flavor transfer. The large capacity of the oven makes it perfect for families or those who love to entertain guests.

Moreover, these cookers feature easy-to-use controls, allowing users to adjust temperatures and settings effortlessly. The easy-clean enamel interior ensures that maintaining the cleanliness of the oven is a simple task, further enhancing the user experience.

In terms of energy efficiency, both the ZCM 650 and ZCM 651 are built to meet modern standards, helping to reduce energy consumption while providing powerful cooking performance.

Overall, the Zanussi ZCM 650 and ZCM 651 gas cookers deliver a blend of style, safety, and high performance, making them ideal options for any home chef looking to elevate their cooking experience.
Top Page Image Contents