Desa MSRBVP Inspecting Burners, Operating Optional GWMT1 Wall Mounted Thermostat, Pilot Assembly

Page 21

OWNER’S MANUAL

OPERATING STOVE WITH B-VENT BURNER SYSTEM

Continued

OPERATING

OPTIONAL GWMT1

WALL MOUNTED

THERMOSTAT

WARNING: Do not connect the thermostat to a power source. Electrical shock and/or a fire haz- ard will occur.

Light the fireplace as instructed in Light- ing Instructions on page 19. Set wall ther- mostat to desired temperature.

This thermostat has been electronically calibrated at the factory and requires no adjustment or leveling.

OPERATING

OPTIONAL BLOWER

ACCESSORY

Blower controls are located on the left side of the rear cover of stove (from front of stove).

The DA3610TA thermostatically-con- trolled blower has an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

If you are using DA3610TA blower with optional thermostat (wall mount or re- mote control), your burner system and blower will not turn on and off at the same time. The burner system may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will con- tinue to run. The blower will shut off after the burner system firebox temperature decreases.

The blower helps distribute heated air from the burner system. Periodically check the top grates of the stove and remove any dust, dirt, or other obstruc- tions that will hinder the flow of air.

Upon installation, the thermostat must be allowed to stabilize at room tempera- ture for a minimum of 30 minutes for proper operation.

To turn the burner system off, adjust thermostat to the lowest setting and turn the gas control knob back to PILOT. The pilot will remain lit.

IMPORTANT: To turn the pilot off, turn the control knob on the heater to the OFF position.

INSPECTING

BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if necessary.

The height of the thermopile must be 3/8" to 1/2" above the pilot flame as shown in Figure 54. The flame from the pilot burner must extend beyond the thermopile.

If your pilot assembly does not meet these requirements:

turn burner system off (see To Turn Off Gas to Appliance, page 19)

see Troubleshooting, pages 23 through 25

Thermopile

3/8" to 1/2"

Pilot Burner

Piezo Ignitor

Figure 54 - Pilot Assembly

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions.

If the vent configuration is installed incor- rectly, the flames will lift or “ghost”. This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.

Figure 55 shows a typical flame pattern. If burnerflamepatterndiffersfromthatdescribed:

turn burner system off (see To Turn Off Gas to Appliance, page 19)

see Troubleshooting, pages 23 through 25

Figure 55 - Typical Flame Pattern

106706

21

For more information, visit www.desatech.com

Image 21
Contents OWNER’S Operation and Installation Manual For Your SafetyFor Your Safety What to do if YOU Smell GAS SUN Valley Stove Company Safety InformationProduct Identification Product FeaturesLocal Codes OperationLocation and Space Requirements PRE-INSTALLATION PreparationStove Body Assembly Cast Iron Stove and B-VENT Burner System AssemblyAttaching Stove Legs Installing Optional Blower Accessory Installing B-VENT Burner System Into Stove BodyGreen Ground Wire Installing Rear CoverVenting Installation Installation PrecautionsType B-VENT Installation Listed B-0 or Greater Installation of Listed B-1 Vent Installing Vent System in a ChaseChecking Vent Capacity High Altitude Installation ChimneysRelining Systems Stove and B-VENT Burner System Installation Troubleshooting Venting ProblemsExternal Regulator with Vent Pointing Down Propane/LP Only Installation Items NeededPressure Testing Gas Supply Piping System Connecting Stove and Burner System to GAS SupplyPressure Testing Burner System Gas Connections Checking GAS ConnectionsChecking Gas Joints for Propane/LP Gas Burner System Installing Optional Wall Mounted Switch GWMS2Installing Remote Receiver Installing Optional Wall Mounted Thermostat GWMT1, GWMS2REMOVING/REPLACING Glass Door Installing 9-Volt Battery in Hand- Held Remote Control UnitInstalling Log No Installing LOGS, Lava ROCK, and Glowing EmbersManual Lighting Procedure For Your Safety Read Before LightingOperating Stove with B-VENT Burner System Lighting InstructionsThermostat Control Operation Optional Remote OperationGhrc Series Operation Ghrcta Series OperationPilot Assembly Operating Optional Blower AccessoryInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatGlass Door Cleaning and MaintenancePilot and Burners LogsObserved Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Gas leak. See Warning statement Technical Service Replacement PartsWiring Diagram Service HintsAccessories SpecificationsMsrbvn Msrbvp Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListIndicates Color Suffix Designation SUN Valley Stove MC* SeriesKEY Part Description QTY International Warranty Information

MSRBVP, MSRBVN specifications

Desa MSRBVN and MSRBVP are two innovative residential community projects that have garnered attention for their design, sustainability, and technological integrations. These developments aim to cater to the growing demand for modern living spaces that balance comfort, efficiency, and environmental responsibility.

One of the main features of Desa MSRBVN and MSRBVP is their careful urban planning. These communities provide an array of housing options, from single-family homes to multi-unit residences, ensuring that there is something for everyone, including families, young professionals, and retirees. The layouts are designed to maximize natural light and airflow, creating a pleasant living environment.

Sustainability is a cornerstone of both projects. The communities incorporate green building practices that reduce their carbon footprint. This includes the use of energy-efficient materials, solar panels for renewable energy generation, and greywater recycling systems that help manage water resources effectively. Landscaping is also thoughtfully designed, with native plants that require minimal irrigation and support local biodiversity.

Technologically, Desa MSRBVN and MSRBVP are at the forefront of smart living. Each home is equipped with advanced home automation systems, allowing residents to control lighting, heating, and security features remotely. Integration with mobile applications provides users with seamless access to their home systems, enhancing convenience and safety.

Safety and community are also pivotal aspects. These developments include well-lit public spaces, walking paths, and recreational areas that encourage outdoor activities and social interaction. Security measures, such as gated entries and surveillance systems, ensure that residents feel secure within their community.

In terms of connectivity, both Desa MSRBVN and MSRBVP benefit from strategic locations that offer easy access to public transportation, shopping centers, schools, and healthcare facilities. This makes daily commutes and lifestyle requirements more manageable for residents.

Overall, Desa MSRBVN and MSRBVP exemplify the future of residential living, where thoughtful design, sustainability, and technology converge to create vibrant and connected communities. As urban areas continue to evolve, such projects highlight the importance of integrating modern living solutions that prioritize residents' well-being and environmental stewardship.