Desa SBVBN(D) Inspecting Burners, Operating Optional GWMT1 Wall Mounted Thermostat

Page 21

OPERATING STOVE WITH B-VENT BURNER SYSTEM

Optional Remote Operation (Cont.)

Operating Optional GWMTY1 Wall Mounted Thermostat

Operating Optional Blower Accessory

INSPECTING BURNERS

Pilot Assembly

Burner Flame Pattern

21

OPERATING STOVE WITH B-VENT BURNER SYSTEM

Continued

Auto Shutoff Feature

1.If the average room temperature exceeds 82 degrees Fahr- enheit (28 degrees Centigrade), the hand-held remote con- trol will perform a safety override and shut the fireplace off. This feature is not available in the MANU mode.

2.The receiver continuously receives signals from the hand- held remote to control the room temperature. If the hand- held remote is misplaced, obstructed, or for any reason cannot transmit to the receiver, the receiver will shut off the fireplace after 8 minutes.

Key Pad Lock Feature

This feature allows the user to lock/unlock the keypad on the hand-held remote in the MANU or AUTO mode to prevent inadvertent operation (i.e. children operating the hand-held re- mote control, etc.). The keypad is locked in either on or off. Press the POWER and LOCK buttons together to turn the unit on or off.

OPERATING OPTIONAL GWMT1

WALL MOUNTED THERMOSTAT

WARNING: Do not connect the thermostat to a power source. Electrical shock and/or a fire hazard will occur.

Light the burner system as instructed in Lighting Instructions on page 19. Set wall thermostat to desired temperature.

This thermostat has been electronically calibrated at the factory and requires no adjustment or leveling.

Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation.

To turn the burner system off, adjust thermostat to the lowest setting and turn the gas control knob back to PILOT. The pilot will remain lit.

IMPORTANT: To turn the pilot off, turn the control knob on the heater to the OFF position.

OPERATING OPTIONAL

BLOWER ACCESSORY

Blower controls are located on the left side of the rear cover when standing in front of stove with burner system installed.

The DA3610TA thermostatically-controlled blower has an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

If you are using DA3610TA blower with optional thermostat (wall mount or remote control) for the burner system, your burner system and blower will not turn on and off at the same time. The burner system may run for several minutes before the blower turns on. After the burner system modulates to the pilot

position, the blower will continue to run. The blower will shut off after the burner system firebox temperature decreases.

The blower helps distribute heated air from the stove. Periodi- cally check the top grates of the stove and remove any dust, dirt, or other obstructions that will hinder the flow of air.

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if necessary.

The height of the thermopile must be 3/8" to 1/2" above the pilot flame as shown in Figure 51. The flame from the pilot burner must extend beyond the thermopile.

If your pilot assembly does not meet these requirements:

•turn burner system off (see To Turn Off Gas to Appliance, page 19)

•see Troubleshooting, pages 23 through 25

Thermopile

3/8" to 1/2"

 

Pilot Burner

Piezo Ignitor

Figure 51 - Pilot Assembly

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions.

If the vent configuration is installed incorrectly, the flames will lift or “ghost”. This can be dangerous. Inspect the flames after installa- tion to ensure proper installation and performance.

Figure 52 shows a typical flame pattern. If burner flame pattern differs from that described:

•turn burner system off (see To Turn Off Gas to Appliance, page 19)

•see Troubleshooting, pages 23 through 25

Figure 52 - Typical Flame Pattern

For morevisit www..com

112127-01A

Page 20 Page 22
Image 21
Page 20 Page 22
Contents For Your Safety What to do if YOU Smell GAS For Your SafetySafety Information Table of ContentsTo operating burner system Product IdentificationProduct Features PRE-INSTALLATION PreparationLocal Codes Stove Body Assembly Cast Iron Stove and B-VENT Burner System AssemblyRemoving Screen Optional Removing Front Surround PanelAmity Models Victor Hearth ModelsInstalling Optional Blower Accessory Installing B-VENT Burner System Into Stove BodySecurely in place before venting pipes are installed Installing Rear CoverInstallation Precautions Venting InstallationVertical Checking Vent CapacityHigh Altitude Installation ChimneysRelining Systems Cast Iron Stove and B-VENT Burner System Installation Troubleshooting Venting ProblemsFlue GAS Spillage Causes of Spillage and Corrective ActionInstallation Items Needed Installing GAS Piping to Stove LocationPressure Testing Gas Supply Piping System Connecting STOVE/BURNER System to GAS SupplyChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaInstalling Optional Wall Mounted Thermostat GWMT1 Installing Optional Wall Mount Switch GWMS2Pressure Testing Burner System Gas Connections Will occurInstalling Battery in Receiver Installing Remote ReceiverREMOVING/REPLACING Glass Door Installing 9-Volt Battery in Hand-Held Remote Control UnitRemove glass door. See Removing/Replacing Glass Door, Installing LOGS, Lava ROCK, and Glowing EmbersManual Lighting Procedure For Your Safety Read Before LightingOperating Stove with B-VENT Burner System Lighting InstructionsOperating Stove with Vent Burner System Optional Remote Thermostat Series OperationON/OFF Series Models Ghrcb and Cghrcb Pilot Assembly Operating Optional Blower AccessoryInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatGlass Door Cleaning MaintenancePilot and Burners LogsObserved Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Above Gas leak. See Warning statementTechnical Service Replacement PartsWiring Diagram Service HintsSbvbnd Sbvbpd SpecificationsModels Sbvbnd and Sbvbpd Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListAmity SCIVF* Series PSCIVF* Series Victor Hearth VH* Series Illustrated Parts BREAKDOWN1LIndicates Color Suffix Designation Amity Stove Body Victor Hearth Stove BodyKEY Part Description QTY Indicates Color Suffix DesignationReceiver and HAND-HELD Remote Control KIT Ghrcb and Cghrcb AccessoriesTHERMOSTATICALLY- Controlled Blower KIT CDA3620TB Stove Hearth Base GC10SPAOwners Registration Form Postage Required 112127-01A Warranty Information

SBVBN(D) specifications

Desa SBVBN(D) is an innovative development that stands out as a beacon of sustainable urban planning and advanced technological integration. Situated in a strategic location, it seeks to create a harmonious blend of modern living and environmental stewardship. The design ethos behind Desa SBVBN(D) revolves around minimizing the ecological footprint while maximizing community well-being.

One of the main features of Desa SBVBN(D) is its commitment to sustainable architecture. Buildings within the community are constructed using eco-friendly materials and designed to harness natural resources effectively. Solar panels are integrated into rooftops, contributing to energy self-sufficiency and significantly lowering energy costs for residents. In addition, rainwater harvesting systems and greywater recycling initiatives ensure responsible water usage, making the community resilient against water scarcity.

The layout of Desa SBVBN(D) emphasizes walkability and connectivity. Wide pedestrian pathways and cycling tracks encourage residents to engage in healthy, active lifestyles while reducing reliance on motor vehicles. Plentiful green spaces, including parks and community gardens, foster social interaction and provide recreational opportunities for families, promoting a sense of belonging among residents.

Technologically, Desa SBVBN(D) is at the forefront of smart city innovations. The implementation of IoT (Internet of Things) devices allows for real-time monitoring of energy usage, traffic patterns, and environmental conditions. Smart lighting systems that adjust based on natural light levels enhance safety while conserving energy. Furthermore, a dedicated app facilitates communication between residents and local authorities, streamlining services and community engagement.

Another distinctive characteristic of Desa SBVBN(D) is its focus on inclusivity and diversity. The community is designed to cater to various demographic groups, offering a range of housing options from affordable units to luxury apartments. Community centers serve as hubs for cultural exchange, educational workshops, and vocational training, empowering residents and fostering a collaborative spirit.

In conclusion, Desa SBVBN(D) represents a forward-thinking approach to urban living, marrying sustainability with technology. With its emphasis on community, resilience, and innovation, it stands as a model for future developments aimed at enhancing the quality of life while protecting the planet for future generations.
Top Page Image Contents