Desa SBVBN(D) Removing Front Surround Panel, Removing Screen Optional, Amity Models

Page 6

6

CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY

Stove Body Assembly (Cont.)

CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY

Continued

10.Attach stove door by inserting step bolt through door hinge pivot hole and into threaded hole in stove body (see Figure 11 and Figure 9 on page 5). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely.

11.Install door catch bolt (M8 x 1.25-55mm with two M8 hex nuts) into threaded hole on stove body (see Figure 9, page 5). Use an adjustable wrench or a 12mm socket. The catch bolt has two hex nuts attached to it (see Figure 12). The top nut is a bolt stop and the bottom nut is for door leveling adjustment.

12.Check general catch bolt alignment with door claw. Make fi- nal adjustment and door leveling after stove is in normal stand- ing position.

13.Carefully lift stove back up on its four attached legs.

Removing Front Surround Panel

Remove 2 bolts from bottom of stove and set aside. Remove bolt from the top of the stove to remove the front panel assembly (see Figure 13).

Removing Screen (Optional)

Amity Models

1.Lay the front panel assembly face down on a protected sur- face. Remove the two screws that hold the front plate onto the front surround plate (see Figure 14). Save these screws.

2.Remove the screws and washers that hold the screen onto the front surround plate. Discard these screws, washers, and screen (see Figure 14).

3.Replace the two screws from step 14 to reassemble the front plate and the front surround plate. Set this assembly aside un- til burner system has been installed, logs have been placed inside of burner system, and glass door to burner system insert has been replaced.

Victor Hearth Models

1.Lay the front panel assembly face down on a protected sur- face. Remove the screws and washers that hold the screen onto the front surround plate. Discard these screws, washers, and screen (see Figure 14).

2.Set this assembly aside until burner system has been installed, logs have been placed inside of burner system, and glass door to burner system insert has been replaced.

Bolt

Stove Body

Front

Assembly

Washers

Bottom Of

 

 

 

 

 

 

 

 

 

Bolt

Stove Unit

 

 

 

 

 

Leg

 

 

Figure 13 - Removing Front Assembly (Amity™ Model Shown)

Figure 10 - Attaching Stove Legs (Amity™

Model Shown)

Front

Screws

 

 

 

 

 

Screw with

 

 

 

 

Surround

 

Washer

 

 

 

 

Plate

 

 

Stove Door

 

 

 

 

 

 

Threaded

Door

 

Bolt Stop

Screw with

 

 

Hole

 

 

 

 

 

 

 

Washer

 

Screen

Door Hinge

 

 

 

 

 

 

 

 

 

 

Screen

 

 

Step

Door Claw

Adjusting

 

 

Front Surround

 

 

Plate and

Bolt

Nut

 

 

 

 

Front Plate

 

Doors

 

 

 

 

 

 

Catch Bolt

 

Amity™

Model

Victor Hearth™ Model

 

 

Figure 14 - Removing Screen from Front Assembly

Bolt Shoulder

Figure 12 - Catch Bolt and

 

 

 

Figure 11 - Attaching Stove Door

 

 

 

Door Claw Orientation

 

 

 

For..com

112127-01A

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For Your Safety For Your Safety What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification To operating burner systemProduct Features PRE-INSTALLATION PreparationLocal Codes Cast Iron Stove and B-VENT Burner System Assembly Stove Body AssemblyAmity Models Removing Front Surround PanelRemoving Screen Optional Victor Hearth ModelsInstalling B-VENT Burner System Into Stove Body Installing Optional Blower AccessoryInstalling Rear Cover Securely in place before venting pipes are installedVenting Installation Installation PrecautionsChecking Vent Capacity VerticalHigh Altitude Installation ChimneysRelining Systems Flue GAS Spillage Troubleshooting Venting ProblemsCast Iron Stove and B-VENT Burner System Installation Causes of Spillage and Corrective ActionInstalling GAS Piping to Stove Location Installation Items NeededChecking GAS Connections Connecting STOVE/BURNER System to GAS SupplyPressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 Psig 3.5 kPaPressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Optional Wall Mounted Thermostat GWMT1 Will occurInstalling Remote Receiver Installing Battery in ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit REMOVING/REPLACING Glass DoorInstalling LOGS, Lava ROCK, and Glowing Embers Remove glass door. See Removing/Replacing Glass Door,Operating Stove with B-VENT Burner System For Your Safety Read Before LightingManual Lighting Procedure Lighting InstructionsOperating Stove with Vent Burner System Optional Remote Thermostat Series OperationON/OFF Series Models Ghrcb and Cghrcb Inspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement AboveWiring Diagram Replacement PartsTechnical Service Service HintsSpecifications Sbvbnd SbvbpdIllustrated Parts Breakdown Models Sbvbnd and SbvbpdParts List KEY Part Number Description QTYIndicates Color Suffix Designation Amity Stove Body Illustrated Parts BREAKDOWN1LAmity SCIVF* Series PSCIVF* Series Victor Hearth VH* Series Victor Hearth Stove BodyIndicates Color Suffix Designation KEY Part Description QTYTHERMOSTATICALLY- Controlled Blower KIT CDA3620TB AccessoriesReceiver and HAND-HELD Remote Control KIT Ghrcb and Cghrcb Stove Hearth Base GC10SPAOwners Registration Form Postage Required 112127-01A Warranty Information

SBVBN(D) specifications

Desa SBVBN(D) is an innovative development that stands out as a beacon of sustainable urban planning and advanced technological integration. Situated in a strategic location, it seeks to create a harmonious blend of modern living and environmental stewardship. The design ethos behind Desa SBVBN(D) revolves around minimizing the ecological footprint while maximizing community well-being.

One of the main features of Desa SBVBN(D) is its commitment to sustainable architecture. Buildings within the community are constructed using eco-friendly materials and designed to harness natural resources effectively. Solar panels are integrated into rooftops, contributing to energy self-sufficiency and significantly lowering energy costs for residents. In addition, rainwater harvesting systems and greywater recycling initiatives ensure responsible water usage, making the community resilient against water scarcity.

The layout of Desa SBVBN(D) emphasizes walkability and connectivity. Wide pedestrian pathways and cycling tracks encourage residents to engage in healthy, active lifestyles while reducing reliance on motor vehicles. Plentiful green spaces, including parks and community gardens, foster social interaction and provide recreational opportunities for families, promoting a sense of belonging among residents.

Technologically, Desa SBVBN(D) is at the forefront of smart city innovations. The implementation of IoT (Internet of Things) devices allows for real-time monitoring of energy usage, traffic patterns, and environmental conditions. Smart lighting systems that adjust based on natural light levels enhance safety while conserving energy. Furthermore, a dedicated app facilitates communication between residents and local authorities, streamlining services and community engagement.

Another distinctive characteristic of Desa SBVBN(D) is its focus on inclusivity and diversity. The community is designed to cater to various demographic groups, offering a range of housing options from affordable units to luxury apartments. Community centers serve as hubs for cultural exchange, educational workshops, and vocational training, empowering residents and fostering a collaborative spirit.

In conclusion, Desa SBVBN(D) represents a forward-thinking approach to urban living, marrying sustainability with technology. With its emphasis on community, resilience, and innovation, it stands as a model for future developments aimed at enhancing the quality of life while protecting the planet for future generations.
Top Page Image Contents