Faber Wall Mount Canopy Rangehood Wiring Diagram, USE and Care Information

Page 9

FOR ALL INSTALLATIONS

1.Install the grease filters using two hands by first pulling and turning the knob to the left so that the locking lever does not protrude from the filter (as in FIGURE 12). Insert the opposite end of the filter into the retaining channel. Insert the knob end next, then turn knob to the right to lock the filter into place.

FIGURE 12

2.Turn the power supply on. Turn on blower and lights. If the rangehood does not operate, check that the circuit breaker is not tripped or the house fuse blown. If the unit still does not operate, disconnect the power supply and check that the wiring connec- tions have been made properly.

WIRING DIAGRAM

• This rangehood uses 20 watt MR-11 halogen lamps w/ cover.

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking vapors and odors from the cooktop area.

For Best Results

Starttherangehoodseveralminutesbeforecookingtodevelopproper airflow. Allow the unit to operate for several minutes after cooking is complete to clear all smoke and odors from the kitchen.

Rangehood Control Panel

The control panel is located on the front edge of the rangehood canopy. The position and function of each control button are indicated in FIGURE 13.

Light On/Off Button ( L )

On/Off switch for the halogen lights. Push the button in to turn the light ON, push again to turn the light OFF.

FIGURE 13

Blower Indicator

Light ( I )

Lights up to indicate blower is ON.

Blower On/Off and Speed Buttons ( 1, 2, 3 )

Push button (1) to turn ON and OFF the blower. This button must be pushed in for the blower to operate regardless of speed chosen. Button (1) operates the blower on LOW speed. Push button (2) for MEDIUM speed. Push button (3) for HIGH speed.

Cleaning

Thestainlesssteelgreasefiltersshouldbecleanedfrequentlyin hot detergent solution or washed in the dishwasher. Stainless steel cleaner should be used on stainless rangehoods. Abrasives and scouring agents can scratch stainless steel finishes and should not be used to clean finished surfaces.

Replacing the Lamps

Before attempting to replace the lamps, make sure that the light switch is turned off. Remove the 2 screws (as indicated in FIGURE 14) that hold the light support and gently pull the support down from the hood. Remove the lamp from the light support and replace with new lamp. Replace the light support and fix it into place with the 2 screws.

An alternative method to replace the lamps is to use a 1 1/4" suction cup (FIGURE 15). Attach the suction cup to the bulb and pull firmly down on the bulb and replace with a new lamp.

FIGURE 14

FIGURE 15

Version 05/08 - Page 9

Image 9
Contents Stilo Lisez Bien Cette Fiche Avant Dinstaller LA HotteDuctwork Venting RequirementsElectrical Requirements For residential use onlyRèglements Dévacuation Fiche Technique ÉlectriqueUniquement pour usage menager Hardware Package Literature Package Plan the InstallationVented to the outside 8 min UpperCabinet base Not vented to the outside 10 min 16 1/8 max Upper Chimney CoverDuctless Install the Rangehood Proceed to for ALL Installations on NextPrepare the Wall For Ductless Installations For ALL InstallationsDiverter Extension USE and Care Information Wiring DiagramFaber Warranty & Service Save for Your Records Plan DE L’INSTALLATION Cheminée Plafond Haut Dimensions d’installatioN Avec ConduitCouvercle cheminée 36 poDextension Pour La Cheminée Plafond Haut Dimensions d’installation Sans ConduitPo min Couvercle cheminée SupérieureInstallation DE LA Hotte Procéder À Pour Tout LES InstallationsPréparation DU MUR Installations Sans Conduit Pour Tout LES InstallationsInstaller le Filtre AU Charbon 6 de la Figure Utilisation ET Entretien Enregistrez Votre Information Ci-dessous