Faber Stilo Isola installation instructions Warranty & Service, USE and Care Information

Page 9

WARRANTY & SERVICE

All Faber products are warranteed against any defect in ma- terials or workmanship for the original purchaser for a period of 1 year from the date of original purchase. This warranty covers labor and replacement parts. The warranty does not cover consumable parts such as filters and light bulbs. This warranty does not apply if this product has been subjected to faulty installation, misuse, or neglect. This warranty excludes any consequential expense or damage resulting from any use or malfunction of the product. All implied warranties are limited to the duration of this warranty.

To obtain warranty service, contact the dealer from whom you purchased the rangehood, or the local Faber distributor. If you cannot identify a local Faber distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking vapors and odors from the cooktop area.

Rangehood Control Panel

The control panel is located on the front edge of the rangehood canopy. The position and function of each control button are indicated in FIGURE 15.

FIGURE 15

Light On/Off Button ( L )

On/Off switch for the halogen lights. Push the button in to turn the light ON, push again to turn the light OFF.

Blower Indicator Light ( I )

Lights up to indicate blower is ON.

Blower On/Off and Speed Buttons ( 1, 2, 3 )

Push button (1) to turn ON and OFF the blower. This button must be pushed in for the blower to operate regardless of speed chosen. Button (1) operates the blower on LOW speed. Push button (2) for MEDIUM speed. Push button (3) for HIGH speed.

For Best Results

Start the rangehood several minutes before cooking to develop proper airflow. Allow the unit to operate for several minutes after cooking is complete to clear all smoke and odors from the kitchen.

Cleaning

The stainless steel grease filters should be cleaned frequently in hot detergent solution or washed in the dishwasher. Stainless steel cleaner should be used on stainless rangehoods. Abrasives and scouring agents can scratch stainless steel finishes and should not be used to clean finished surfaces.

Replacing the Lamps

Before attempting to replace the lamps, make sure that the light switch is turned off. Remove the 2 screws (as indicated in FIGURE 16) that hold the light support and gently pull the support down from the hood. Remove the lamp from the light support and replace with new lamp. Replace the light support and fix it into place with the 2 screws.

FIGURE 16

Version 04/05 - Page 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Read and Save These Instructions Lisez Bien Cette Fiche Avant Dinstaller LA HotteVenting Requirements Electrical RequirementsFor residential use only Règlements Dévacuation Additionell Règlements DévacuationFiche Technique Électrique Avertissement Pour Minimiser LES RisquesParts Supplied for Installation Tools Needed for InstallationParts Needed for Installation Optional Accessories AvailableVented to the outside Plan the InstallationCooktop distance x in Figure MinNot vented to the outside 8 min15 3/8 max Installing the Rangehood For Ductless InstallationsAttach the Support Make the Electrical ConnectionMake the Internal Electrical Connections USE and Care Information Warranty & ServiceFuse Model 5 X 20 5A time delay Fuse Replacement if NeededDéballer LA Hotte Installation DU SupportCalcul DE Longueur DU Conduit La FigurePlan DE LʼINSTALLATION Dimensions DʼINSTALLATION Avec Conduit36 po Table de cuisson Dimensions DʼINSTALLATION Sans ConduitInstallations Sans Conduit Installation DU HotteBrancher LE Câble Dalimentation Connecter LES Connecteurs Interne AvertissementUtilisation ET Entretien Garantie ET ServiceCette hotte utilise des ampoules halogènes de 20 W Changement DES Fusibles
Top Page Image Contents