Faber AXIA ISOLA Attach the Support, For ductless installations, Install the Canopy

Page 5

ATTACH THE SUPPORT

1.Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

2.Determine and clearly mark with a pencil on the ceiling where the rangehood will be installed.

3.Atemplate (ItemAin Figure 5) for mounting the support is supplied in the carton with the support. Use this template to mark holes for support on the ceiling. The chimney must be disassembled to reveal the support. The Upper Chimney (Item B in Figure 5) is held in place by two screws which must be removed.

IMPORTANT NOTE: BE CAREFUL

WHEN DETERMINING THE

LOCATION FOR THE HOLE IN

YOUR CEILING FOR THE DUCT

WORK. THIS HOLE SHOULD

NOT BE CENTERED OVER THE

CENTER OF THE COOKING

SURFACE AS THE DUCT WORK

THAT RUNS UP INSIDE THE

CHIMNEY AND THROUGH THE

CEILING IS NOT IN THE CENTER

OF THE CHIMNEY.

FIGURE 5

4.Determine and make necessary cuts for the ductwork. The duct opening is shown on the mounting template (Item E in Figure 5). Install ductwork before mounting the support.

5.Determine the proper location for the Power Supply Cable as indicated on the template. Use a 1 1/4" Drill Bit to make this hole. Run the Power Supply Cable. Use caulking to seal around the hole. DO NOT turn on the power until installation is complete! A knockout is provided near the exhaust exit on the canopy for the Power Supply Cable.

6.Attach the Upper Support to the ceiling (Item A in Figure 6). Make sure that the support is firmly attached to the ceiling. Install the Lower Support (Item C in Figure 6). The canopy height over the range is determined by the length of the support. The bottom of the canopy will be approximately 2 5/8 inches below the bottom of the support. Once the length of the support is determined, tighten the four screws using an Allen Wrench (Item D in Figure 6) to secure the Lower Support in place. All four screws must be firmly tightened

FIGURE 6

before attaching the canopy.

7.Remove the cover from the field wiring compartment. Remove the wiring electrical knockout using a flat-blade screwdriver. DO NOT turn on the power until installation is complete! Connect the Power Supply Cable to the rangehood. Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connector. Attach the Black lead of the power supply to the Black lead of the rangehood with a twist-on type wire connector. Connect the Green (Green and Yellow) ground wire under the Green grounding screw.

8.Attach the duct work to the top of the blower. Make sure to seal all joints with duct tape to prevent leaks.

For ductless installations:

Ductless installations require a ductless kit. This kit consists of one upper chimney cover with a hole for the exhaust air (Item A in Figure 7), a vent grid to cover the hole in the chimney cover (Item B in Figure 7), a ductless diverter assembly (Item C in Figure 7), and two charcoal filters (Item D in Figure 7). The ductless diverter must be installedbefore the upper chimney cover. The chimney cover without a vent hole will not be needed for this installation and should be discarded.

Before installing the upper chimney cover, the vent grid assembly must be installed. The bottom of this assembly must attach to the blower (Item F in Figure 7). The upper end must be positioned at the opening in the upper chimney support (Item E in Figure 7). Install the ductless diverter assembly. The charcoal filters will be installed after the rangehood is completely installed.

FIGURE 7

INSTALL THE CANOPY

1.Remove the grease filters and set aside. The grease filters are removed by pressing the handle in front of the filter. When replacing, make sure the filters are properly positioned with the handles visible in front.

Version 02/02 - Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Read and Save These Instructions Lisez Bien Cette Fiche Avant Dinstaller LA HotteElectrical Requirements Venting RequirementsFiche Technique Électrique Règlements DévacuationCalculate the Ductrun Length Plan the InstallationUnpack the Rangehood Attaching the SupportAttach the Support For ductless installationsInstall the Canopy Turn the power supply on. Turn on blower USE and Care Information Warranty & ServiceDéballer LA Hotte Installation DU SupportCalcul DE LA Longueur DU Conduit Installation DE LA Hotte Pour les installations sans conduitAvertissement Utilisation ET Entretien Garantie ET Service

AXIA ISOLA specifications

The Faber AXIA ISOLA is a sophisticated kitchen hood that embodies the perfect blend of style, innovation, and functionality. Designed with the modern kitchen in mind, this range hood offers exceptional performance and aesthetics, making it an ideal choice for those who value both form and function in their cooking space.

One of the standout features of the AXIA ISOLA is its sleek, contemporary design. It has a minimalist aesthetic that complements various kitchen styles, from ultra-modern to traditional. Available in different finishes such as stainless steel or glass, the AXIA ISOLA seamlessly integrates into any kitchen décor, serving as both a powerful ventilation solution and an eye-catching centerpiece.

The AXIA ISOLA employs cutting-edge technologies that enhance its effectiveness. One such technology is the high-performance motor, which ensures efficient air extraction, eliminating smoke, odors, and pollutants from the kitchen environment. Additionally, the hood incorporates advanced noise-reduction technologies, allowing for quiet operation even at high speeds. This makes it perfect for open concept kitchens, where cooking and socializing often happen simultaneously.

Another notable characteristic of the Faber AXIA ISOLA is its versatile installation options. Designed for both ducted and recirculating installations, the hood offers flexibility depending on kitchen layout and planning. This allows homeowners to maximize their kitchen's functionality without compromising on design.

The AXIA ISOLA features intuitive controls, often equipped with touch-sensitive buttons or remote-control functionality, allowing users to easily adjust settings from a distance. Additionally, integrated LED lighting illuminates the cooking area effectively, enhancing visibility while also being energy-efficient.

Cleaning and maintenance are also simplified, thanks to its stainless-steel construction and dishwasher-safe filters. These features reduce the effort needed to keep the hood looking and operating like new.

Overall, the Faber AXIA ISOLA is more than just a kitchen hood; it is a combination of elegance, innovation, and practicality. Perfect for culinary enthusiasts and home cooks alike, it elevates the cooking experience while ensuring a clean and fresh kitchen environment. With its advanced technologies and stylish design, the AXIA ISOLA is an investment in both the functionality and aesthetics of any modern kitchen.
Top Page Image Contents