Hunter Fan 41949-01 manual R n i n g

Page 2

W a r n i n g

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.Use this unit only in a manner intended by the manufacturer. If you have questions, contact the manufacturer.

2.Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3.Installation work and electrical wiring must be done by quali- fied person(s) in accordance with all applicable codes and standards, including fire-rated construction.

4.Sufficient air is needed for proper combustion and exhausting of gasses through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufac- turer’s guideline and safety standards,such as those published by the National Fire Prevention Association (NFPA), and the

American Society for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities.

5.When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities.

6.Ducted fans must always be vented to the outdoors.

7.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

8.Never place a switch where it can be reached from a tub or shower.

9.Install fan at least 5 feet (1.52 m) above the floor.

10.This unit must be grounded.

11.Unit must not be installed in a ceiling thermally insulated to a value greater than R40.

C A U T I O N

1.For general ventilating use only. Do not use to exhaust hazard- ous or explosive materials and vapors.

2.To avoid motor bearing damage and noisy/unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3.DO NOT install this product in a wall. This product is designed for installation in ceilings up to a 12/12 pitch (45 degrees). Ductwork must point upward.

4.Please read specification label on product for further information and requirements.

W a r n i n g

DISCONNECT ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL BEFORE

SERVICING UNIT

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove motor plate, find the single tab on the motor plate (located next to the receptacle). Push up rear motor plate tab while pushing out on the side of the housing or insert a screwdriver into the slot in the housing (next to tab) and twist screwdriver. Gently vacuum fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the motor with the exact service motor. You should replace the impeller at the same time.

COOKING AREA

 

Do Not Install Above

 

Or Inside This Area

 

45°

45°

 

 

Cooking

Floor

 

 

 

Equipment

 

41949-01 02/12/2008

011_41949_EngS_2-12-08.indd 2

2/12/08 2:43:22 PM

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Installation I d e R n i n g Before Installation For replacementsRemove the motor/blower from the housing A11 New Construction attaching to joistA14 A15A21 A18A19 A22B15 B11B13 New Construction suspended between joistsB20 B17B19 B26 B22B24 B25 B27C12 Existing Construction accessible from aboveC11 C13 C14C15C16 C17C21 C22C29 C25C26 C28D12 Existing Construction accessible only from belowD11 D13D19 D20 D16D17 D18 Attaching the Grille D22D23 01141949EngS2-12-08.indd 12/08 24408 PM Trouble Shooting SolutionWarranty Limited WarrantyÍ a S t a l a c i ó n V E R T E N C I a Antes de la instalación No incluidoRetire el motor/soplador del alojamiento Construcción nueva fijación a la viga Conecte los alambres como se muestra Vaya al paso Construcción nueva suspendido entre vigas De pulgApriete los tornillos B24 Cuelgue DEL Mazo DE CablesSIN Ventilador Existente Construcción existente accesible desde arribaTaladre un agujero en el centro de cada perfil Apriete los tornillos del aliviador de tensiones Vaya al paso En la página 37 para Fijar la rejilla Construcción existente accesible sólo desde abajo Vuelva a instalar el motor introduciendo las pestañas y Fijación de la rejilla 01141949Sp2-12-08.indd 12/08 24644 PM Solución de problemas SoluciónGarantía Garantía Limitada

41949-01 specifications

The Hunter Fan 41949-01 ceiling fan is a remarkable blend of elegance and functionality, designed to enhance both the aesthetics and comfort of any space. With its sleek modern design and powerful performance, it stands out as a top choice for homeowners seeking a reliable cooling solution.

One of the main features of the Hunter Fan 41949-01 is its whisper-quiet operation, which is achieved through the use of advanced motor technology. The fan is equipped with a powerful but silent motor that enables smooth and efficient airflow without creating distracting noise, making it ideal for bedrooms, living rooms, or any room where peace and tranquility are appreciated.

The fan is designed with a contemporary style that complements various interior decor themes. Its clean lines and minimalist design ethos ensure it fits seamlessly into both modern and traditional spaces. Available in multiple finishes, it allows homeowners to choose a look that best suits their personal style.

In terms of performance, the Hunter Fan 41949-01 boasts a generous blade span that facilitates optimal air circulation. The fan features three aerodynamic blades that are specially engineered to move air efficiently. This ensures not only a comfortable environment during hot summers but also assists in heat distribution during cooler months, thus making it a year-round asset.

Energy efficiency is another key characteristic of this fan. It utilizes Energy Star-rated technology, which means it consumes less power while delivering high airflow, ultimately assisting homeowners in reducing their electricity bills. Furthermore, its durable construction and high-quality materials ensure longevity, offering both an economical and environmentally friendly option.

Versatility is reinforced by the inclusion of a remote control, allowing users to easily adjust the fan’s speed settings and lighting without having to get up. The fan also comes with integrated LED lights, providing bright and energy-efficient illumination, elevating the functionality of the space.

In summary, the Hunter Fan 41949-01 represents a sophisticated fusion of style, performance, and energy efficiency. Its quiet operation, advanced airflow technology, and versatile design make it an attractive addition to any home, ensuring comfort and enhancing living spaces for years to come.
Top Page Image Contents