Zanussi ZSF 4112 What to do, when, Flashing fault code appears, Fault Possible cause Solutions

Page 15

What to do, when...

Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer.

...a flashing fault code appears

The dishwasher will not start or stops during operation. All push buttons are inoperative except for the On/Off push button and a combination of indicator lights, as indicated in the following chart, are flashing. Open the dishwasher’s door and carry out the following suggested corrective actions.

Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made, even if the appliance is in guarantee.

	Fault code / malfunction		Possible cause	Solutions

	- Indicator light of the		The water tap is blocked or furred with	Clean the water tap.
	programme in progress is		limescale.
	flashing.
	flashing.		The water tap is turned off.	Turn the water tap on.
	- 1 flash of the indicator		The water tap is turned off.	Turn the water tap on.

			The filter (where present) in the threaded hose	Clean the filter in the threaded hose
	light "End of cycle".		The filter (where present) in the threaded hose	Clean the filter in the threaded hose
			fitting at the water inlet valve is blocked.	fitting.

	The machine does not fill with		The water inlet hose has not been correctly laid	Check the water inlet hose connection.
	water.		The water inlet hose has not been correctly laid	Check the water inlet hose connection.
	water.		or it is bent or squashed.
			or it is bent or squashed.

	- Indicator light of the		The siphon is blocked.	Clean out the siphon.
	programme in progress is
	flashing.
	flashing.		The water drain hose has not been correctly laid	Check the water drain hose connection.
	- 2 flashes of the indicator light		The water drain hose has not been correctly laid	Check the water drain hose connection.
	- 2 flashes of the indicator light		or it is bent or squashed.
	"End of cycle".		or it is bent or squashed.
	"End of cycle".
	The dishwasher will not drain.

	- Indicator light of the		Protection against flooding is active.	Close the water tap and contact the
	programme in progress is			Service Force Centre.
	flashing.
	- 3 flashes of the indicator light
	"End of cycle".

Once the checks have been carried out, close the door and press the push button of the programme that was running before the intervention of the alarm, the programme will continue from the point in which it was interrupted. If the fault code reappears contact the Service Force Centre.

For other combinations of fault codes not described in the above chart will appear, please contact your Service Force Centre.

...there are problems when operating the dishwasher

	Fault		Possible cause	Solutions

			The dishwasher door has not been properly	Close the door.
	The programme does not start		closed.

			The main plug is not plugged in.	Insert the mains plug.
			The main plug is not plugged in.	Insert the mains plug.

			The fuse has blown in the household fuse box.	Replace the fuse.

	There is a whistling noise during		The whistling is not a cause for concern.	Use a different brand of detergent.
	washing

15

Image 15

Contents Dishwasher Contents Disposal Safety instructionsInstallation Child safetyDescription of the appliance Examples Prior to using for the first timeIndicator light Water softenerTo fill Filling with saltDeactivation/activation of the dosage of rinse aid Adjusting the doseRinse aid Filling with rinse aidAre of limited suitability Daily useLoading cutlery and dishes Lower basketTo move to the higher position proceed as follows Adjusting the height of the upper basketCutlery basket Upper basketFill with detergent Use of detergentCombi detergents Different kinds of detergentDetergent tablets Concentrated detergent Washing programmes Press the On/Off push button Setting and starting the programmeTo interrupt or cancel a washing programme in progress Starting a washing programmeProlonged periods of non-operation Maintenance and cleaningCleaning the filters Frost precautionsFault Possible cause Solutions Flashing fault code appearsThere are problems when operating the dishwasher Fault code / malfunction Possible cause SolutionsWater drops have dried onto glasses and dishes Dishes are not cleanWash results are not satisfactory Dishes are wet and dullCustomer Care Department Service and Spare PartsExclusions Guarantee ConditionsStandard Guarantee Conditions European GuaranteeWater supply connections Installation instructionsFitting under a counter LevellingWater outlet hose connection Electrical connectionGreen and Yellow Earth Blue- Neutral Brown- Live Cup racks position a Hints for test centresPage Page From the Electrolux Group. The world’s No.1 choice