Zanussi Understanding Dishwasher Error Codes and Solutions
Page 15

What to do, when...

Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer.

...a fault code appears

The dishwasher will not start or stops during operation.

Open the dishwasher’s door.

The intervention of an alarm is indicated by:

-continuous flashing of the indicator light of the running programme,

-a combination of flashes and pauses of the END OF CYCLE indicator light and by intermittent audible signals (as described in the chart).

Carry out the following suggested corrective actions.

Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made, even if the appliance is in guarantee.

Fault code / malfunction

Possible cause

Solutions

 

 

 

 

 

- continuous flashing of the

The water tap is blocked or furred with

Clean the water tap.

indicator light of the running

limescale.

 

 

programme

 

 

 

The water tap is turned off.

Turn the water tap on.

- 1 intermittent audible signal

 

 

 

 

 

 

The filter (where present) in the threaded hose

Clean the filter in the threaded hose

- 1 flash of the END OF CYCLE

fitting at the water inlet valve is blocked.

fitting.

indicator light

 

 

 

 

The machine does not fill with

The water inlet hose has not been correctly laid

Check the water inlet hose connection.

or it is bent or squashed.

 

 

water.

 

 

 

 

 

 

 

 

 

 

- continuous flashing of the

The sink spigot is blocked.

Clean out the sink spigot.

indicator light of the running

 

 

 

 

 

 

 

 

programme

The water drain hose has not been correctly laid

Check the water drain hose connection.

- 2 intermittent audible signals

or it is bent or squashed.

 

 

- 2 flashes of the END OF

 

 

 

CYCLE indicator light

 

 

 

The dishwasher will not drain.

 

 

 

 

 

 

- continuous flashing of the

Anti-flood device has activated.

Close the water tap and contact the

indicator light of the running

 

Service Force Centre.

programme

 

 

 

- 3 intermittent audible signals

 

 

 

- 3 flashes of the END OF

 

 

 

CYCLE indicator light

 

 

 

 

 

 

 

 

Once the checks have been carried out, press the programme selection/cancel button and close the dishwasher’s door. The programme will continue from the point at which it was interrupted. If the fault code reappears contact our local Service Force Centre.

For other combinations of fault codes not described in the above chart, please contact your local Service Force Centre.

...there are problems when operating the dishwasher

Malfunction

Possible cause

Solutions

 

 

 

 

 

 

The dishwasher door has not been properly

Close the door.

The programme does not start

closed.

 

 

 

The main plug is not plugged in.

Insert the mains plug.

 

 

 

 

 

 

 

 

The fuse has blown in the household fuse box.

Replace the fuse.

 

 

 

There is a whistling noise during

The whistling is not a cause for concern.

Use a different brand of detergent.

washing

 

 

 

 

 

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Dishwasher Contents Disposal Safety instructionsInstallation Child safetyDescription of the appliance Audible signals Programme indicator lightsDeactivation/activation of the audible signals Prior to using for the first time Setting manuallyWater softener Filling with rinse aid Adjusting the doseFilling with dishwasher salt Rinse aidAre of limited suitability Daily useLoading cutlery and dishes Lower basketUpper basket Cutlery basketFill with detergent Adjusting the height of the upper basketUse of detergent To move to the higher position proceed as followsCombi detergents Different kinds of detergentDetergent tablets Concentrated detergentWashing programmes Unloading the dishwasher To interrupt or cancel a washing programme in progressTo cancel a washing programme in progress Starting a washing programmeProlonged periods of non-operation Maintenance and cleaningCleaning the filters Frost precautionsMalfunction Possible cause Solutions Fault code appearsThere are problems when operating the dishwasher Fault code / malfunction Possible cause SolutionsWater drops have dried onto glasses and dishes Dishes are not cleanWash results are not satisfactory Dishes are wet and dullCustomer Care Department Service and Spare PartsExclusions Guarantee ConditionsStandard guarantee conditions European GuaranteeFixing to the adjacent units Installation instructionsBuilding-in LevellingProceed as follows Water outlet hose connectionElectrical connection Green and Yellow Earth Blue- Neutral Brown- LiveCup racks position a Hints for test centresPage Page From the Electrolux Group. The World’s No.1 choice

ZDT 6053 specifications

The Zanussi ZDT 6053 is an impressive built-in dishwasher that combines efficiency, convenience, and performance to meet the demands of busy households. Known for its sleek design and practicality, this model stands out in the crowded dishwasher market.

One of the primary features of the Zanussi ZDT 6053 is its spacious interior, accommodating up to 13 place settings. This makes it ideal for families or those who frequently entertain guests. The adjustable upper basket allows for flexible loading options, providing ample space for larger pots and dishes, while the cutlery tray ensures organized and efficient cleaning of utensils.

Efficiency is a hallmark of the Zanussi ZDT 6053, with an energy rating of A++. This means it operates with lower energy consumption while still delivering excellent cleaning results. Additionally, it boasts a range of wash programs, including Eco, Intensive, and Quick options, which cater to various cleaning needs. The Quick Wash program, in particular, is a time-saver, offering clean dishes in as little as 30 minutes, perfect for those in a hurry.

The appliance is equipped with innovative technologies designed to enhance performance. The Auto Open Door feature, for instance, helps with drying efficiency by allowing steam to escape at the end of the cycle, ensuring that dishes are dried effectively without the need for additional energy. Meanwhile, the Soft Touch controls provide an intuitive user experience, simplifying the selection of wash programs.

Noise levels are another significant consideration in modern dishwashers, and the Zanussi ZDT 6053 does not disappoint, operating at a quiet 47 dB. This low noise level makes it suitable for open-plan living spaces, ensuring that conversations are not interrupted during operation.

Safety features are also integral to this model. The Zanussi ZDT 6053 includes a child lock mechanism that prevents accidental operation, making it a safe choice for families with young children.

In conclusion, the Zanussi ZDT 6053 is a versatile and reliable built-in dishwasher that combines spacious design, efficiency, and advanced technologies. Whether you are cleaning everyday dishes or hosting larger gatherings, this model offers customizable options to suit your needs while maintaining an eco-friendly profile. With its user-friendly features and excellent performance, the Zanussi ZDT 6053 is a worthy addition to any modern kitchen.
Top Page Image Contents