Tricity Bendix SI 452 installation instructions Introduction, Rating Plate, Installation

Page 8

INTRODUCTION

WARNING: THIS APPLIANCE MUST BE EARTHED

RATING PLATE

Record the model and serial numbers on the back cover of this instruction book, from the rating plate. This is situated on the lower front frame of the appliance and can be seen upon opening the oven door.

The appliance must be protected by a suitably rated fuse or circuit breaker. The rating of the appliance is given on the rating plate.

INSTALLATION

If your cooker has been damaged in transit, contact your supplier immediately. DO NOT attempt to install it.

Your cooker left the factory fully packaged to protect it from damage. If it is delivered without packaging and damage has occurred, the manufacturer cannot accept responsibility. Contact your supplier for advice.

Once the packaging has been removed the cooker should only be moved by hand. DO NOT use a sack barrow or any other aid to lift the cooker as damage may occur.

Connection to the electricity supply must be carried out by a qualified electrician/competent person.

The electrical connection should be made using a double pole isolating switch (cooker socket) with at least 3mm contact separation. The cable must have conductors of sufficiently high cross-sectional area to prevent overheating and deterioration.

Six square millimetres (6.00mm²) is the recommended cross-section area.

The cable should be routed away from potentially hot areas marked by X in the diagram below.

To move the cooker, open the main oven door and lift the cooker by holding inside the top of the compartment.

This is a type Y appliance which means it is free-standing and can be fitted with cabinets on one or both sides. It may also be fitted in a corner setting.

Side walls which are above hob level should be protected by heat resistant non-combustible material and MUST NOT be nearer than 40mm to the hob side.

A nominal air gap of 2mm all around the cooker is required to enable the cooker to be moved into position.

A spacer has been incorporated into the back of the appliance to ensure an air gap of 10mm is maintained at hotplate level. Tiles or other forms of deep wall covering should not obscure this gap.

8

Image 8
Contents Better Products. Better Value Technical Details Model NO. SIContents Contents Preface Safety During OperationAfter USE GeneralRating Plate InstallationIntroduction General Notes on Using Your Cooker Reversible Main Oven DoorAbout Condensation and Steam Push to Turn ControlsControl Panel FeaturesGetting to Know Your Cooker Programmer Minute MinderHOW to SET the Oven Timer Control To SET the Timer to Switch on and OFF AutomaticallyReturning the Cooker to or to Cancel AN Automatic Programme To SET the Timer to Switch OFF onlyThings to Note Hints and Tips Ceramic HOBRecommended Saucepans HOT HOB Indicator Deep FAT FryingPreserving Special Frying NoteDual Grill Uses of the GrillSelecting the Grill Grill PAN and HandleGrilling Chart Food Shelf Grill TimeTOP Oven Uses of the TOP OvenSelecting the TOP Oven To FIT the TOP Oven ShelfLHINTS and Tips Automatic CookingSelecting the FAN Oven Main FAN OvenUses of the FAN Oven To FIT the Main Oven Shelves Oven Cooking Chart FAN Oven TOP Oven Food Shelf Cooking Approx Position Temp CRoasting Chart Roasting ChartSelecting Defrost Defrost FeatureUses of Defrost Feature Care and Cleaning To Remove Discolourations or White and Silver Marks To Reduce HOB SoilageCare of Stayclean Surfaces Cleaning the Outside of the CookerCleaning Inside the GRILL/OVEN Compartments Cleaning Between the Outer and Inner Door Glass To Clean Inside the Inner Glass DoorReplacing the Oven Light Bulb To Remove the Outer GlassSomething not WORKING? Cooker does not work at allService and Spare Parts ServiceHelp US to Help YOU Consumer Care DepartmentCustomer Service Centres Centre Postal Districts Service Address AppointmentsEH FK G KA KY1-16 ML Lancaster Shrewsbury Guarantee Conditions ExclusionsPage SI 452 Page Better Products. Better Value Rating Plate Reference