System Startup, Changing the Filter | Frigidaire 241856001 specification

Automatic Ice & Water Dispenser (continued)

PureSource TM* Ice and Water Filter (some models)

Order new filter cartridges through the dealer where you bought the refrigerator, contact the Electrolux Solutions Hotline at 1-800-944-9044, or go to our web site at www.frigidaire. com. It might be good to order some filter cartridges when you first install your refrigerator. Be sure to ask for the RG-100 PureSource™* replacement cartridge.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter cartridge has already been installed in the filter housing at the factory. Refer to the How to Prime the Water Supply System section to properly fill the system with water.

The PureSource™ * NGRG-2000 Ice and Water Filter System with the RG-100 cartridge is tested and certified by NSF International, the

nationally recognized and respected, not for profit, certification organization for public health

safety. The PureSource™* system is tested and certified to ANSI/NSF Standard 42. See performance data sheet for specifications. This system should not be used on water that is microbiologically unsafe or with water of unknown quality unless the water has been adequately disinfected before or after traveling through the filtration system.

•Rated Capacity - 400 gallons

•Rated service flow - .5 GPM

•Maximum Rated Pressure - 100 PSI, Minimum 30 PSI

•Maximum Operating Temp. - 100°F, Minimum 33°F

Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every 6 - 9 months normally will ensure the highest possible water quality. Ice jams in the ice maker and/or hollow ice cubes (partially frozen cubes with water inside), may also be a sign that your water filter needs changing. The Filter Status light will turn red after 400 gallons of water has flowed through the ice and water dispenser. Also, if the filter has been in a refrigerator that has not been in use for awhile (during moving for example), change the filter before reinstalling the refrigerator. The dispenser system will also operate without filtration (with filter cartridge removed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1Open freezer door and leave open until filter change is complete.

2Turn OFF side mounted ice maker by raising wire signal arm to the UP position. Turn OFF rear mounted ice maker by pressing ON/OFF power switch to the “O” position.

3Hold filter cup firmly, and unscrew towards left. (Some water could leak out as you remove cup. This is normal.) Filter cartridge should come down with cup. If cartridge remains in housing, pull down gently, while twisting filter back and forth.

4Rinse out cup under running water.

5The large o-ring that seals the filter system fits in the o-ring groove inside the cup. Should the o-ring fall out during filter cartridge replacement, simply place it back in the groove prior to screwing the cup back in place. If the o-ring becomes damaged, you will need to order one from the Electrolux Solutions Hotline.

6Discard old filter cartridge.

7Remove new filter cartridge from packaging. Place in cup. The end with the small o-ring should be up, out of the cup.

8Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is completely tightened with PureSource™ logo facing outward. Do Not Tighten

Past Stop.

9Turn ON side mounted ice maker by lowering wire signal arm to the DOWN position. Turn ON rear mounted ice maker by pressing ON/OFF power switch to the “I” position.

10Check for leaks. Open refrigerator door. Wipe any water droplets from the filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and reinsert the filter cartridge. Check placement of large O-ring. Reinstall filter cup, making certain it is tightened completely.

11To prime filter system and purge air from water line, continue flushing the system for approximately 3 minutes to assure that the purest water possible is stored in

the water tank. There will be noticeable spurts and sputters as the system pushes air out through the system and out the dispenser nozzle. This is normal.

IMPORTANT

Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to press the Filter Status Reset button located on the ice and water dispenser. This will reset the Filter Status light. Push the Reset button until the green, red and amber lights flash (10-15 seconds). Please refer to the complete dispenser operating instructions attached to the inside of the freezer door.

On models without a Filter Status reset button, there is a set of Reminder Stickers included in the envelope that the Use

&Care Manual came in. Choose a dated sticker that indicates

6 - 9 months (depending on your water quality and usage) from the date of installation. Place the sticker on the front of the filter cup to remind you when it is time to change the filter.

*White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.

241856001 specifications

The Frigidaire 241856001 is a highly regarded refrigerator replacement part known for its reliability and efficiency. Specifically designed for various Frigidaire models, this component plays a vital role in maintaining optimal performance within the refrigerator system.

One of the main features of the 241856001 is its compatibility with a wide range of Frigidaire refrigerator models. This flexibility makes it a popular choice for homeowners and technicians alike, as it can easily replace older or worn-out parts and ensure continued functionality. The part is engineered to meet or exceed original specifications, which guarantees that users benefit from the same quality and performance as the original component.

The 241856001 is built with durable materials that are designed to withstand the rigors of daily use. This durability not only enhances the longevity of the product but also minimizes the need for frequent replacements, making it a cost-effective solution for anyone looking to keep their refrigerator running smoothly.

One notable technology incorporated in this part is its energy-efficient design. In an age where energy consumption is a pressing concern, the Frigidaire 241856001 contributes to lower energy bills by ensuring that the refrigerator operates at its most efficient capacity. This emphasis on energy efficiency aligns with modern consumers’ desires for sustainable and environmentally friendly appliances.

The installation of the 241856001 is straightforward, making it accessible for those who prefer DIY maintenance. Clear instructions are typically included, ensuring that users can confidently replace the component without needing professional assistance. This ease of installation is a significant advantage, as it saves both time and money.

Additionally, the Frigidaire 241856001 boasts a compact design that allows it to fit seamlessly within the confines of the fridge’s architecture. This characteristic ensures that the refrigerator maintains its aesthetic appeal while benefiting from the reliable functionality of this part.

Overall, the Frigidaire 241856001 is a crucial component that enhances the performance of various Frigidaire refrigerator models. With its compatibility, durability, energy efficiency, and easy installation process, it stands out as an excellent choice for those looking to replace or upgrade their refrigerator parts. Whether you are a homeowner or a technician, you can trust the Frigidaire 241856001 to deliver the quality and performance needed for a well-functioning refrigerator.