Frigidaire 241856001 Connecting Water Supply, To Avoid Property Damage

Connecting Water Supply

WARNING

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.

To Connect Water Supply Line To Ice Maker Inlet Valve

1Disconnect refrigerator from electric power source.

2Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.

3Remove plastic cap from water valve inlet and discard cap.

CAUTION

To Avoid Property Damage:

•Copper or stainless steel braided tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for supply line.

•DO NOT install water supply tubing in areas where temperatures fall below freezing.

•Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT

Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need:

•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver.

•Access to a household cold water line with water pressure between 30 and 100 psi.

•A water supply line made of ¼ inch (6.4 mm) OD, copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

•A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

•A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve.

4If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch/6.4 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1.

If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2.

5With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.

6Coil excess water supply line (copper tubing only) about 2½ turns behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

7Turn ON water supply at shutoff valve and tighten any connections that leak.

8Reconnect refrigerator to electrical power source.

9To turn ice maker on, lower wire signal arm (side mounted) or set the ice maker’s On/Off power switch to the “I” position (rear mounted).

	Steel
Plastic Water Tubing	Clamp
to Ice Maker	Brass
Fill Tube
	Compression
	Nut
	Ferrule
	(Sleeve)
	Copper
	water line
	Water Valve
	Bracket
	Valve Inlet
	Water Valve
Copper water line
from household water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1	Figure 2

NOTE

Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/state building codes, Electrolux recommends for homes with existing valves its Smart Choice water line kit 5305513409 (with a 6 ft. stainless steel water line) and for homes without an existing valve, Electrolux recommends its Smart Choice water line kit 5304410264 (with a 20 ft. copper water line with self-tapping saddle valve). Please refer to www.frigidaire.com/store for more information.

IMPORTANT

After connecting the water supply, refer to “How to Prime the Water Supply System” for important information about priming an empty water supply system.

Your refrigerator’s water supply system includes several tubing lines, a water filter, a water valve, and a water tank.To ensure that your water dispenser works properly, this system must be completely filled with water when your refrigerator is first connected to the household water supply line.

4