Frigidaire FDB2410HIC specifications Pump Assembly, Product Specifications, Heater

Pump Assembly

The pump assembly is driven by a synchronous motor. The motor drives a pump which supplies 100 percent filtered water

Draining is accomplished by using a small separate synchronous drain pump mounted to the side of the sump. The drain pump is connected to the main pump by a small rubber hose. The drain check valve is located at the discharge end of the drain pump. The drain hose

The drain hose must have a loop at a minimum height of 32 inches in order to insure proper drainage.

Product Specifications

Electrical

Rating 120 Volts, 60Hz

Separate Circuit..15 amp min.- 20 amp max.

Motor (Amps)	0.6 - 0.9
Heater Wattage	475 - 630W
Total Amps (load rated)	7.0
TempAssure	135°F ±5°F
(60°C±3°C) [with outer door in place]
TempBoost	140°F ±5°F
Heated Wash/Heated Rinse

Water Supply

Suggested minimum incoming water

temperature	120°F (49°C)
Pressure (PSI) min./max		20/120
Connection (NPT)		3/8"
Consumption (Normal Cycle)
..........................................	5.2 - 5.6 U.S. gal
Water valve flow rate (U.S. GPM)		0.9
Water recirculation rate (U.S. GPM)
.................................................	approx. 5.28

Trouble Shooting Tips

Personal Injury Hazard

Always disconnect the dishwasher from the electrical power source before adjusting or replacing components.

Symptom Check the Following Remedy

is attached by a clamp to the discharge end of the drain pump.

Hi-Limit Thermostat 200°F (93°C)

Water fill time 36 sec.

Dishwasher will not operate when turned on.

1.	Fuse (blown or tripped).
2.	120 VAC supply wiring connection
	faulty.

1.	Replace fuse or reset breaker.
2.	Repair or replace wire fasteners at
	dishwasher junction box.

Heater

Refer to the cycle chart on the reverse side to Voltage checks of the heater should be made in determine when the heater is on during the the dry portion of the service test mode. wash cycle. The heater cycles ON and OFF for

brief periods during the drying cycle.

3.	Electronic control board defective.
4.	No 12 VAC power to control.
5.	Motor (inoperative).
6.	Door switch (open contacts).
7.	Door latch not making contact with
	door switch.
8.	Touch pad circuit defective.
9.	No indicator lamps illuminate when
	START or OPTIONS are pressed.

3.	Replace control board.
4.	Replace control board.
5.	Replace motor/impeller assembly.
6.	Replace latch assembly.
7.	Replace latch assembly.
8.	Replace console assembly.
9.	Replace console assembly.

Standard Dry Air Flow

The heated, moist air leaving the dishwasher	The water on the dishes is evaporated into drier
through the console vent causes drier air to be	air and the venting process continues. The
drawn into the unit by way of intake vents located	heating element is turned ON and OFF during the
at the bottom of the door.	entire drying cycle.

Motor hums but will not start or run.	1.	Motor (bad bearings).	1.	Replace motor assembly.
	2.	Motor stuck due to prolonged	2.	Rotate motor impeller.
		non-use.
Motor trips out on internal thermal	1.	Improper voltage.	1.	Check voltage.
overload protector.	2.	Motor windings shorted.	2.	Replace motor/impeller assembly.
	3.	Glass or foreign items in pump.	3.	Clean and clear blockage.
Dishwasher runs but will not heat.	1.	Heater element (open).	1.	Replace heater element.
	2.	Electronic control board defective.	2.	Replace control board.

Detergent and Rinse Aid Dispenser

The detergent and rinse aid dispenser is a one piece component consisting of a molded detergent cup and a built-in rinse aid dispenser.

The detergent cup has a spring loaded cover and the rinse aid dispenser has a removable cover.

Liquid rinse aid is added to the dispenser up to the fill line indicator. The amount of rinse aid released can be adjusted by turning the arrow indicator from one, being the least amount, to four, being the greatest amount.

To replace dispenser:

•shut off electricity to dishwasher,

•remove outer door panel assembly,

•disconnect wiring to the actuator,

•remove the six screws,

•remove the dispenser,

•replace and reinstall screws,

•rewire actuator.

	3.	Wiring or terminal defective.	3.	Repair or replace.
	4.	Hi-Limit thermostat defective.	4.	Replace thermostat.
Detergent cover will not latch or	1. Latch mechanism defective.		1.	Replace dispenser.
open.	2. Electronic control board defective.		2.	Replace control board.
	3.	Wiring or terminal defective.	3.	Repair or replace.
	4.	Broken spring(s).	4.	Replace dispenser.
	5.	Defective actuator.	5.	Replace dispenser.
Dishwasher will not pump out.	1. Drain restricted.		1.	Clear restrictions.
	2.	Electronic control board defective.	2.	Replace control board.
	3.	Defective drain pump.	3.	Replace pump.
	4.	Blocked impeller.	4.	Check for blockage, clear.
	5.	Open windings.	5.	Replace pump assembly.
	6.	Wiring or terminal defective.	6.	Repair or replace.
Dishwasher will not fill with water.	1. Water supply turned off.		1.	Turn water supply on.
	2.	Defective water inlet fill valve.	2.	Replace water inlet fill valve.
	3.	Check fill valve screen for	3.	Disassemble and clean screen.
		obstructions.	4.	Repair or replace.
	4.	Defective float switch.
	5.	Electronic control board defective.	5.	Replace control board.
	6.	Wiring or terminal defective.	6.	Repair or replace.
	7.	Pressure Switch Stuck.	7.	Repair or replace.
Dishwasher water siphons out.	1. Drain hose (high) loop too low.		1.	Repair to proper 32-inch minimum
				height.
	2.	Drain line connected to a floor drain	2.	Install air gap at counter top.
		not vented.

Detergent left in dispenser.	1. Detergent allowed to stand too long in		1.	Instruct customer/user.
		dispenser.	2.	Instruct customer/user.
	2.	Dispenser wet when detergent was
		added.	3.	Instruct customer/user on proper
	3.	Detergent cover held closed or blocked
		by large dishes.		loading of dishes.
	4.	Improper incoming water	4.	Incoming water temperature of
		temperature to properly dissolve		120°F is required to properly
		detergent.		dissolve dishwashing detergents.
	5.	See "Detergent cover will not open."

020905