5.0 | Setting the | |
|
|
|
Figure 3: Mounting Hole Locations | 5.0 | Setting the | ||||
|
|
|
| Address |
| |
| 3 |
|
| Each keypad must have its address set | ||
|
|
|
| |||
| 1 |
|
| with its address pins. The keypads must | ||
|
|
| also be programmed at the control panel. | |||
|
|
|
| |||
|
| 4 | Figure 5: | |||
| 3 |
| ||||
| 2 |
|
|
|
| |
| 2 | Address 1 | Address 2 | Address 3 | ||
|
|
| ||||
|
|
| 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | |
| Back of |
| Address 4 | Address 5 | Address 6 | |
| 3 | 3 | 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | |
1 - Holding tabs for reference guides | Address 7 | Address 8 | Address 9 | |||
|
|
|
| |||
2 - | Release tab |
| 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | |
| Address 10 | Address 11 | Address 12 | |||
3 - | Mounting Hole |
| ||||
| 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | |||
4 - | Wire Entrance |
| ||||
| Address 13 | Address 14 | Do not use | |||
|
|
| ||||
|
|
| 1 2 3 4 5 6 7 8 | 1 2 3 4 5 6 7 8 | address 15 | |
|
|
|
|
Do not secure the base at this point. | Select the keypad address |
|
|
|
|
| Place the shorting jumpers over the address pins as | |
|
|
|
|
| shown in Figure 5. | |
Figure 4: | Inside View of |
| Each option bus device must have its own | |||
|
|
|
|
|
| |
|
| 7 | 6 | 5 |
| address, and each address can only |
|
|
| support one device. | |||
|
|
|
|
|
| |
| 1 |
|
| 8 | 6.0 | Wiring the |
|
|
|
|
| Be sure all wiring is | |
|
|
|
| 1 |
| |
2 |
|
|
| 4 |
| routing. Keypad wiring cannot be run with |
|
|
|
| smoke detector wiring, NAC wiring or MUX | ||
|
|
| 8 |
| ||
3 |
|
|
|
| loop wiring. | |
|
|
| 3 |
| ||
|
|
|
|
| For the | |
|
|
|
|
| current draw from the auxiliary power is 500 mA for | |
|
|
| Red |
| keypads. The maximum length of wire (all branches | |
|
|
| Black |
| ||
|
|
| Green |
| added together) that can be connected to the option | |
|
|
| Yellow |
| ||
|
| Connector Cable Orientation |
| bus terminals is 4000 ft (1,219 m). | ||
|
|
|
|
| The maximum length between any one device and | |
|
|
|
|
| the panel terminals depends on the current drawn | |
1 - | Wire Entrance |
|
| on the branch that the device is on. The current | ||
2 - | Internal Sounder |
|
| draw on a particular branch can be found by adding | ||
3 - | Mounting Hole |
|
| together the individual current draws of each device | ||
|
| connected to the branch. | ||||
4 - Address jumper pins |
| |||||
| Refer to the | |||||
5 - | Control Keys |
|
| |||
|
| (P/N: F01U008458) for detailed wire length | ||||
6 - | Reset switch |
|
| |||
|
| calculations. | ||||
7 - |
| |||||
|
|
| ||||
8 - | Lock |
|
|
|
|
|
4 |
|
|
|
| Bosch Security Systems, Inc. 9/08 |