Frigidaire FFEF4017LB To Start the Self-Clean Cycle, To Set the Controls for a Self-Clean Cycle

Page 20

SETTING MAIN OVEN CONTROLS - MODEL B & C

SELF-CLEANING

To Start the Self-Clean Cycle

*We recommend a 2 hour self-clean cycle for light soils, and a 3 hour cycle for average to heavy soils (to assure satisfactory results).

To Set the Controls for a Self-Clean Cycle:

1.Be sure the clock shows the correct time of day.

2.Push the CLEAN pad. "- - -" appears in the display.

3.Push the UP ARROW pad until "3:00" appears in the display for a 3 hour cycle, or push the DOWN ARROW pad until "2:00" appears in the display for a 2 hour cycle.

4.As soon as the UP or DOWN ARROW pad is released, "CLn" appears in the display.

5.As soon as the controls are set, the motor driven lock will begin to close automatically and the "Door Locked" indicator light will flash. DO NOT open the door while the light is flashing (it takes about 15 seconds for the lock to close).

6.The "Door Locked" light will glow until the cleaning cycle is completed or cancelled, and the oven temperature has cooled.

When the Self-Clean Cycle is Completed:

1.The time of day will appear in the display window and the "Door Locked" light will continue to glow.

2.Once the oven has cooled down for about 1 hour and the "Door Locked" light has gone out, the oven door can be opened.

Stopping or Interrupting a Self-Cleaning Cycle

If it becomes necessary to stop or interrupt a self- cleaning cycle due to excessive smoke or fire:

1.Push the CLEAR OFF pad.

2.Once the oven has cooled down for about 1 hour and the "Door Locked" light has gone out, the oven door can be opened.

3.Correct the condition which caused the smoking.

4.Restart the self-clean cycle once all conditions have been corrected.

CAUTION

Use care when opening the oven door after self-clean- ing cycle. Stand to the side of the oven when opening the door to allow hot air or steam to escape.

DO NOT force the oven door open. This can damage the automatic door locking system. Use caution when opening the door after the self-cleaning cycle is com- pleted. The oven may still be VERY HOT.

FAILURE MODES

All failure modes give a visual and audible alarm. When display shows F10 (temperature runaway), F30 (oven sensor circuit fault) or F90 (motor door lock fault), the electronic oven control has detected a fault condition. Note that code and push the CLEAR OFF pad to clean the display and stop the beeping. Reprogram the oven. If fault recurs, push CLEAR OFF pad, disconnect the appliance to prevent damage and contact an authorized servicer.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Use &Care Product Welcome & CongratulationsRegister Your Product Important Safety Instructions DefinitionsImportant Instructions for Using Your Cooktop Know which knob controls each surface heating unitImportant Safety Instructions for Using Your Oven Important Safety Instructions for Cleaning Your OvenSELF-CLEANING Oven only For Glass Cooktop onlyFeatures AT a Glance Model a Your Range FeaturesModel B Features AT a Glance Features AT a Glance Model C Cookware material types Before Setting Surface ControlsUsing proper cookware Setting Surface Controls Surface Cooking SettingsElement on indicator light Coil surface elementsGriddle Recommended Settings For the Griddle FoodTo Operate the Griddle model C only Before Setting Oven Controls Oven vent locationAir circulation in the oven Arranging oven racksModel a Setting Main Oven Controls To Change the Temperature Display ModeTo SET the Minute Timer Press Timer ON/OFF padSetting Main Oven Controls Model a To SET or Change the Temperature for BakingAdjusting Your Oven Temperature To BroilFor a Silent Control Panel Model B & C Setting Main Oven ControlsOven can be Programmed to To SET Control for Oven Lockout Setting Main Oven Controls Model B & CTo SET Control for Continuous Bake or 12 Hour Energy Saving To SET or Change the Temperature for Normal Baking Setting BroilTo Set the Controls for Normal Baking Broiling TipsTo SET the Bake Time Feature Recalibrating Your Oven TemperatureWhen the Set Bake Time Runs Out To Adjust Oven TemperatureWhat to Expect during Cleaning SELF-CLEANINGAdhere to the following cleaning precautions When the Self-Clean Cycle is Completed To Start the Self-Clean CycleTo Set the Controls for a Self-Clean Cycle Model B & C Setting Auxiliary Oven Controls To BakeRack Position From Top Food Broil Stop PositionCleaning various parts of your appliance Surfaces How to CleanCare & Cleaning General CleaningSurface Elements and Drip Bowls To Replace the Light Bulb Cleaning the Griddle some modelsChanging oven light Removing and replacing the main oven door some models To remove and replace the main oven door some modelsTo Remove Oven Door To Replace Oven DoorStorage Drawer some models To Remove the Storage DrawerTo Replace the Storage Drawer To Remove Storage DrawerOven baking Be accessible for Service Entire range or ovenCode error ex. F10 Range is not levelSelf-cleaning cycle Soil not completely removed after self- cleaning cycleAreas Discoloration withPage Major Appliance Warranty Exclusions This warranty does not cover the following
Top Page Image Contents