Frigidaire 318203821E warranty Removing and Replacing the Oven Door, Changing Oven Light

Page 24

Care & Cleaning

Hinge lever

Hinge hook support

Lock engaged for door

removal - Figure 1

HINGE SLOT - Door removed from the oven - Figure 2

Hinge

lever

Lock in normal position - Figure 3

Removing and Replacing the Oven Door

The door is heavy. For safe, temporary storage, lay the door flat with the inside of the door facing down.

To Remove Oven Door:

1.Open the door to the fully opened position.

2.Pull up the lock located on both hinge supports and engage it in the hinge lever hooks (Figure 1).You may have to apply a little downward pressure on the door to pull the locks fully over the hinge lever hooks.

3.Grab the door by the sides and pull the bottom of the door up and toward you to disengage the hinge supports. Keep pulling the bottom of the door toward you while rotating the top of the door toward the range to completely disengage the hinge levers (Figure 2).

4.To clean oven door, follow the instructions provided in the General Care & Cleaning table.

To Replace Oven Door:

1.Grab the door by the sides; place the hinge supports in the hinge slots. Open the door to the fully opened position.

2.Disengage the lock from the hinge lever hooks on both sides (Figure 3).

Note: Make sure the hinge supports are fully engaged before unlocking the hinge levers.

3.Close the oven door.

Special Door Care Instructions - Most oven doors contain glass that can break. Read the following recommendations:

1.Do not close the oven door until all the oven racks are fully in place.

2.Do not hit the glass with pots, pans, or any other object.

3.Scratching, hitting, jarring or stressing the glass may weaken its structure causing an increased risk of breakage at a later time.

To Remove the "Hidden Bake" Cover (some models)

1.In order to remove the "hidden bake" cover, pull the back edge with one hand about 1/2" inch and lift up the "hidden bake" cover with both hands. (See picture)

2.When reinstalling the "hidden bake" cover, be sure to put it all the way to the back of the oven and lay it down on the 2 shoulder screws. Then push the front edge of the cover in its place below the front bracket.

To have easier access to the "hidden bake" cover, you can remove the oven door by following the instructions on previous page.

IMPORTANT: Always replace the "hidden bake" cover before the next use.

Changing Oven Light

Be sure the oven is unplugged and all parts are COOL before replacing the oven light bulb. Do not turn the oven light on during the self-cleaning cycle. High temperature will reduce lamp life.

The interior oven light will turn on automatically when the oven door is opened.

The oven light may be turned on when the door is closed by using the oven light switch located on the control panel.

On a self clean oven the lamp is covered with a glass shield held in place by a wire holder.

THIS GLASS SHIELD MUST BE IN PLACE WHENEVER THE OVEN IS IN USE.

To replace the light bulb:

CAUTION: BE SURE OVEN IS COOL

1. Turn the power off at the main source.

2. Wear a leather-faced glove for protection against possible broken glass.

3. Replace bulb with a 40 watt appliance bulb only.

4.For self-cleaning oven, press wire holder to one side to release glass shield, change bulb and be sure to replace glass shield.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Before Setting Oven Controls 13-14 Care & Cleaning 18-25 Adjusting YourWarranty Back Cover WelcomeWelcome & Congratulations Questions?Versión en español Register Your ProductImportant Safety Instructions SLIDE-IN Models onlyImportant Instructions for Using Your Cooktop Know which knob controls each surface heating unitImportant Instructions for Using Your Oven Avoid scratching the cooktop glass with sharp ob- jectsFeatures At a Glance BridgeDual Setting Surface Controls Setting Type of CookingModels with Coil Elements Models with Ceramic Glass Cooktop About the Ceramic Glass CooktopAbout the Radiant Surface Elements Locations of the Radiant Surface Elements and ControlsSurface Cooking Settings Models with Ceramic Glass Cooktop Available Esec Display SettingsRecommended Settings for Single, Bridge Electronic Surface Element Control Esec some modelsHot Surface Indicator Lights Esec Error Indicator Message ErEsec Lockout Feature To Operate the Single Surface ElementsSmall Element Large To Operate the Dual Surface ElementTo Operate the Bridge Surface Element Model a Only Before Setting Oven Controls Surface cookingSelecting Surface Cooking Cookware Cookware Material typesSetting Oven Controls Arranging Oven RacksOven Vent Location -Models with Ceramic Glass Cooktop Removing and Replacing Oven RacksSetting Warmer Drawer Control If Equipped Warmer Drawer Temperature SelectionArranging Warmer Warm & Ready Drawer Rack Positions Operating the Warmer DrawerBaking Problems and Solutions Chart Cooking InformationsBroiler Clean-Up Tips some models PreheatingTo Broil Determining Broiling TimesCare & Cleaning Cleaning Various Parts of Your RangeSurfaces How to Clean Cooktop Cleaning Coil Surface Element Models Only Porcelain enamelCooktop, surface under Cooktop Insert Control PanelCooktop Cleaning- Coil Surface Element Models Only Cooktop Cleaning Porcelain enamel Cooktop ModelsPorcelain enamel cooktop cleaning instructions some models Cleaning Recommendations for the Ceramic Glass Cooktop Plastic or foods with a high sugar contentFor light to moderate soil For heavy, burned on soilOven Cleaning Cleaning the Regular Oven non self-clean oven, some modelsAluminum utensils Cleaning the Self-Clean Oven some models Removing and Replacing the Oven Door To Remove the Hidden Bake Cover some modelsChanging Oven Light Adjusting Your Oven Temperature To Remove and Replace Warmer Drawer some modelsStorage Drawer with extensible glides some models Storage Drawer some modelsSolutions to Common Problems Before you callAvoid Transportation Damage to your Range Major Appliance Warranty Information Exclusions
Top Page Image Contents