GE EGR3001, JGBP40 Operating the Self, How to Set the Oven for Cleaning, To Stop a Clean Cycle

Page 27

www.GEAppliances.com

How to Set the Oven for Cleaning

Quick Reminder:

1.Latch the door.

2.Turn the Oven Set knob to CLEAN.

If the oven is too hot and you start to set a clean cycle, you will not be able to slide the latch.

Allow additional time for cooling before you try to set the cycle.

1.Follow directions to prepare the oven for cleaning.

2.Slide the latch handle to the right as far as it will go.

Never force the latch handle. Forcing the handle will damage the door lock mechanism.

3.Turn the Oven Set knob to CLEAN. The CLEAN, AUTOMATIC OVEN, OVEN ON and COOK TIME ON/OFF lights will glow.

NOTE: If you turn the Oven Set knob before you slide the latch, the CLEAN light will flash. Slide the latch to the right.

Clean cycle time is normally 4 hours and

20 minutes. On some models, you can change the Clean Time to anywhere between 3 hours and 5 hours and 59 minutes, depending on how dirty your oven is.

You have one minute to change your Clean Time. Use the HOUR and MIN. pads to change the total Clean Time.

Both the OVEN ON light and the CLEAN light will flash when the Clean Time is finished.

After using the clean cycle, the door latch and the Oven Set knob must be returned to their original positions before you can use the oven.

When the CLEAN light flashes, slide the latch handle to the left as far as it will go, turn the Oven Set knob to OFF and open the door.

Never force the latch handle. Wait until the CLEAN light flashes and the latch slides easily. Forcing the latch handle may damage the door lock.

Operating the Self-

To Stop A Clean Cycle

1.Turn the Oven Set knob to OFF.

2.Wait until the oven has cooled below the locking temperature to unlatch the door. You will not be able to open the door right away unless the oven has cooled below the locking temperature.

Cleaning Oven

After a Clean Cycle

You may notice some white ash in the oven. Just wipe it up with a damp cloth after the oven cools.

If white spots remain, remove them with a soap- filled steel wool pad. Be sure to rinse thoroughly with a vinegar and water mixture. These deposits are usually a salt residue that cannot be removed by the clean cycle.

NOTE:

•You cannot set the oven for cooking until the oven is cool enough for the door to be unlatched.

•While the oven is self-cleaning, you can press the CLOCK pad to display the time of day. To return to the clean countdown, press the COOK TIME ON/OFF pad.

If the oven is not clean after one clean cycle,

(continued next page)

 

repeat the cycle.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Installation Instructions If you received a damaged range… Save time and money. Before you request service…Help US Help YOU… Read this guide carefullyFor your safety, never use your appliance Important Safety InstructionsImportant Safety Instructions When You Get Your RangeSurface Cooking Save These Instructions Clean only parts listed in this Use and Care GuideFeatures and appearance vary Features of Your RangeFeatures of Your Range Surface Cooking Surface Cooking Top-of-Range CookwareDo not use a wok on a support ring. Placing Cook Time ON/OFF. Press this for Timed Baking operations Features of Your Oven ControlOven CONTROL, Clock and Timer Oven Control, Clock and TimerYour Oven Control Using Your Oven Automatic Oven Shut Off Using Your OvenOven Shelves Shelf PositionsHow to Set Your Range for Baking BakingType of Food Shelf Position Baking OvenDon’t Peek PiesCakes Baking PansTimed Baking How to Time BakeHow to Set Immediate Start and Automatic Stop Timed BakingQuick Reminder How to Set Delay Start and Automatic StopQuestions and Answers Can I use the minute timer during oven cooking?How to Set for Regular Baking/Roasting Sabbath FeatureHow to Exit the Sabbath Feature Adjust the Oven Thermostat Adjust the Oven ThermostatTo Adjust the Thermostat Roasting Dual Shelf CookingUse of Aluminum Foil Roasting Guide Why is my roast crumbling when I try to carve it?Roasting Guide RoastingShould I salt the meat before broiling? Why are my meats not turning out as brown as they should?Broiling Oven door must be closed during broilingBroiling Guide Broiling GuideOperating the SELF-CLEANING Oven Before a Clean CycleDo not rub or clean the door gasket Clean cycle time is normally 4 hours How to Set the Oven for CleaningTo Stop a Clean Cycle After a Clean CycleWhy do I have ash left in my oven after cleaning? How to Set Delay Start of Cleaning on some modelsCan I clean the woven gasket around the oven door? Should there be any odor during the cleaning?Operating Care and CleaningSelf-Cleaning Oven Care CleaningFor proper ignition Sealed Burner Assemblies on some modelsOven Bottom Care and CleaningBurner Grates Cooktop SurfaceOutside of the door Lift-Off Oven DoorBroiler Pan and Grid Inside of the doorOven Light Replacement on some models Control Panel and KnobsRemovable Storage Drawer on some models Oven Air Vents Removable Kick Panel on some modelsStainless Steel Surfaces on some models For Your Safety Installation InstructionsImportant Safety Instructions General Provide Adequate GAS Supply Rigid Pipe Hookup for Models Equipped with Sealed Burners Electrical Requirements Extension Cord CautionsIMPORTANT-Please read carefully Electric Disconnect Yellow flames Electric Ignition ModelsTo remove the oven bottom Leveling the Range ⁄ 8 ″ Problem Possible Cause QUESTIONS? Before YOU Call for SERVICE…Do not Work Before You Call for ServiceFood does not GE Service Protection Plus Warranty Registration Department Box Louisville, KYNo Matter What Brand Model Number Serial Number Consumer Product Ownership RegistrationWarranty Consumer Support GE Appliances Website

JGBP40, JR EGR3000, EGR3001 specifications

The GE EGR3001, JR EGR3000, and JGBP40 are three innovative industrial equipment models from General Electric, renowned for their efficiency and advanced engineering.

The GE EGR3001 represents a significant advancement in gas turbine technology. This model is designed for optimal performance in combined cycle power plants, where its high efficiency helps to reduce fuel consumption and greenhouse gas emissions. The EGR3001 features an advanced combustor design that facilitates low emissions and enhances fuel flexibility, allowing it to operate on various fuels, including natural gas and liquid fuels. This flexibility is crucial in today's energy markets, where energy source availability may fluctuate.

The EGR3001 is also equipped with sophisticated control systems that provide reliable performance even under varying load conditions. Its modular design simplifies maintenance, allowing for faster service times and lower operational costs. Additionally, the EGR3001's robust construction ensures durability and longevity, making it an excellent investment for power generators.

The JR EGR3000 is another remarkable model in GE's lineup, focusing on integration and performance in industrial settings. This unit combines the features of a gas turbine with superior steam generation capabilities. The JR EGR3000 prides itself on its compact design, which facilitates easy installation without compromising performance. It features advanced aerodynamics and heat recovery systems that maximize output while minimizing fuel consumption.

A key highlight of the JR EGR3000 is its digital twin technology, which allows operators to simulate and analyze performance in real-time. This technology provides valuable insights for maintenance planning and operational efficiency, leading to decreased downtime and optimally managed assets.

The JGBP40 is a unique offering, primarily designed for industrial applications requiring higher efficiency and reliability. It integrates advanced gearbox technology with high-speed turbine operations, facilitating increased torque and power output. The JGBP40 is designed for versatility, able to support various applications across different industries.

Its design incorporates advanced materials to withstand high-stress conditions, thereby increasing operational lifespan. The model also features smart diagnostics and predictive maintenance capabilities, allowing operators to monitor health and performance efficiently. This proactive approach minimizes unplanned outages and enhances overall productivity.

In summary, the GE EGR3001, JR EGR3000, and JGBP40 are testament to General Electric’s commitment to innovation, efficiency, and reliability in industrial equipment. Their advanced features and technologies not only optimize performance but also address modern energy challenges, making them essential assets for electricity producers and industrial users alike.
Top Page Image Contents