GE EGR3001, JR EGR3000, JGBP40 manual Oven Light Replacement on some models, Control Panel and Knobs

Page 33

www.GEAppliances.com

Oven Light Replacement (on some models)

CAUTION: Before replacing your oven light bulb, disconnect the electrical power to the range at the main fuse or circuit breaker panel. Be sure to let the light cover and bulb cool completely.

The oven light bulb is covered with a removable glass cover that is held in place with a bail-shaped wire. Remove the oven door, if desired, to reach cover easily.

To remove:

1.Hold a hand under the

cover so it doesn’t fall

 

when released. With

 

fingers of the same

 

hand, firmly push back

 

the wire cover holder.

 

Lift off the cover.

Wire cover holder

DO NOT REMOVE ANY SCREWS TO REMOVE COVER.

2.Do not touch hot bulb with a wet cloth. Replace bulb with a 40-watt household appliance bulb.

To replace cover:

1.Place it into the groove of the light receptacle. Pull the wire forward to the center of the cover until it snaps into place. When in place, the wire holds the cover firmly. Be certain the wire is in the depression in the center of the cover.

2.Connect electrical power to the range.

Control Panel and Knobs

It’s a good idea to wipe the control panel after each use of the oven. Clean with mild soap and water or vinegar and water, rinse with clean water and polish dry with a soft cloth.

Do not use abrasive cleansers, strong liquid cleaners, plastic scouring pads or oven cleaners on the control panel—they will damage the finish. A 50/50 solution of vinegar and hot water works well.

The control knobs may be removed for easier cleaning. To remove a knob, pull it

straight off the stem. If knob is difficult to remove, place

a towel or dishcloth between

the knob and control panel and pull gently.

Wash the knobs in soap and water or a vinegar and hot water solution.

Metal parts can be cleaned with soap and water. Do not use steel wool, abrasives, ammonia, acids or commercial oven cleaners. Dry with a soft cloth.

Care and Cleaning

Removable Storage Drawer (on some models)

The storage drawer is a good place to store cookware and bakeware. Do not store plastics and flammable material in the drawer.

The storage drawer may be removed for cleaning under the range. Clean the storage drawer with a damp cloth or sponge. Never use harsh abrasives or scouring pads.

To remove storage drawer:

1.Pull drawer straight

out until it stops.

2. Tilt the front of the drawer up and free of the range.

To replace storage drawer:

1.Set the stops on the back of the drawer over the stops in the range.

2.Slide drawer evenly and straight back, so that the rails in the range are engaged.

(continued next page)

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Installation Instructions Help US Help YOU… Save time and money. Before you request service…Read this guide carefully If you received a damaged range…Important Safety Instructions Important Safety InstructionsWhen You Get Your Range For your safety, never use your applianceSurface Cooking Save These Instructions Clean only parts listed in this Use and Care GuideFeatures and appearance vary Features of Your RangeFeatures of Your Range Surface Cooking Surface Cooking Top-of-Range CookwareDo not use a wok on a support ring. Placing Cook Time ON/OFF. Press this for Timed Baking operations Features of Your Oven ControlOven CONTROL, Clock and Timer Oven Control, Clock and TimerYour Oven Control Using Your Oven Oven Shelves Using Your OvenShelf Positions Automatic Oven Shut OffHow to Set Your Range for Baking BakingType of Food Shelf Position Baking OvenCakes PiesBaking Pans Don’t PeekHow to Set Immediate Start and Automatic Stop How to Time BakeTimed Baking Timed BakingQuestions and Answers How to Set Delay Start and Automatic StopCan I use the minute timer during oven cooking? Quick ReminderHow to Set for Regular Baking/Roasting Sabbath FeatureHow to Exit the Sabbath Feature Adjust the Oven Thermostat Adjust the Oven ThermostatTo Adjust the Thermostat Roasting Dual Shelf CookingUse of Aluminum Foil Roasting Guide Why is my roast crumbling when I try to carve it?Roasting Roasting GuideBroiling Why are my meats not turning out as brown as they should?Oven door must be closed during broiling Should I salt the meat before broiling?Broiling Guide Broiling GuideOperating the SELF-CLEANING Oven Before a Clean CycleDo not rub or clean the door gasket To Stop a Clean Cycle How to Set the Oven for CleaningAfter a Clean Cycle Clean cycle time is normally 4 hoursCan I clean the woven gasket around the oven door? How to Set Delay Start of Cleaning on some modelsShould there be any odor during the cleaning? Why do I have ash left in my oven after cleaning?Self-Cleaning Oven Care Care and CleaningCleaning OperatingFor proper ignition Sealed Burner Assemblies on some modelsBurner Grates Care and CleaningCooktop Surface Oven BottomBroiler Pan and Grid Lift-Off Oven DoorInside of the door Outside of the doorOven Light Replacement on some models Control Panel and KnobsRemovable Storage Drawer on some models Oven Air Vents Removable Kick Panel on some modelsStainless Steel Surfaces on some models For Your Safety Installation InstructionsImportant Safety Instructions General Provide Adequate GAS Supply Rigid Pipe Hookup for Models Equipped with Sealed Burners Electrical Requirements Extension Cord CautionsIMPORTANT-Please read carefully Electric Disconnect Yellow flames Electric Ignition ModelsTo remove the oven bottom Leveling the Range ⁄ 8 ″ Problem Possible Cause QUESTIONS? Before YOU Call for SERVICE…Do not Work Before You Call for ServiceFood does not GE Service Protection Plus Warranty Registration Department Box Louisville, KYNo Matter What Brand Model Number Serial Number Consumer Product Ownership RegistrationWarranty Consumer Support GE Appliances Website

JGBP40, JR EGR3000, EGR3001 specifications

The GE EGR3001, JR EGR3000, and JGBP40 are three innovative industrial equipment models from General Electric, renowned for their efficiency and advanced engineering.

The GE EGR3001 represents a significant advancement in gas turbine technology. This model is designed for optimal performance in combined cycle power plants, where its high efficiency helps to reduce fuel consumption and greenhouse gas emissions. The EGR3001 features an advanced combustor design that facilitates low emissions and enhances fuel flexibility, allowing it to operate on various fuels, including natural gas and liquid fuels. This flexibility is crucial in today's energy markets, where energy source availability may fluctuate.

The EGR3001 is also equipped with sophisticated control systems that provide reliable performance even under varying load conditions. Its modular design simplifies maintenance, allowing for faster service times and lower operational costs. Additionally, the EGR3001's robust construction ensures durability and longevity, making it an excellent investment for power generators.

The JR EGR3000 is another remarkable model in GE's lineup, focusing on integration and performance in industrial settings. This unit combines the features of a gas turbine with superior steam generation capabilities. The JR EGR3000 prides itself on its compact design, which facilitates easy installation without compromising performance. It features advanced aerodynamics and heat recovery systems that maximize output while minimizing fuel consumption.

A key highlight of the JR EGR3000 is its digital twin technology, which allows operators to simulate and analyze performance in real-time. This technology provides valuable insights for maintenance planning and operational efficiency, leading to decreased downtime and optimally managed assets.

The JGBP40 is a unique offering, primarily designed for industrial applications requiring higher efficiency and reliability. It integrates advanced gearbox technology with high-speed turbine operations, facilitating increased torque and power output. The JGBP40 is designed for versatility, able to support various applications across different industries.

Its design incorporates advanced materials to withstand high-stress conditions, thereby increasing operational lifespan. The model also features smart diagnostics and predictive maintenance capabilities, allowing operators to monitor health and performance efficiently. This proactive approach minimizes unplanned outages and enhances overall productivity.

In summary, the GE EGR3001, JR EGR3000, and JGBP40 are testament to General Electric’s commitment to innovation, efficiency, and reliability in industrial equipment. Their advanced features and technologies not only optimize performance but also address modern energy challenges, making them essential assets for electricity producers and industrial users alike.
Top Page Image Contents