GE JGBP40, EGR3001, JR EGR3000 manual Surface Cooking

Page 8

SURFACE COOKING

Surface Burner Controls

The knobs that turn the surface burners on and off are located on the control panel in front of the burners.

The two knobs on the left control the left front and left rear burners. The two knobs on the right control the right front and right rear burners.

Before Lighting a Burner

•If drip pans are supplied with your range, they should be used at all times.

•Make sure all grates on the range are in place before using any burner.

On ranges with sealed burners:

•The smaller burner (right rear position) will give the best simmer results. It offers precise cooking performance for delicate foods, such as sauces or foods which need to cook over low heat for a long time. It can be turned down to a very low simmer setting.

•The right front burner is higher powered than the others and will bring liquids to a boil quicker.

•On some models, the burners are all the same size and power.

To Light a Surface Burner

Push the control knob in and turn it to LITE. You will hear a little ‘‘clicking’’ noise—

the sound of the electric spark igniting the burner.

Turn the knob to adjust the flame size. If the knob stays at LITE, it will continue to click.

When one burner is turned to LITE, all the burners spark. Do not attempt to disassemble or clean around any burner while another burner is on. An electric shock may result, which could cause you to knock over hot cookware.

In case of power failure, you can light the surface burners on your range with a match. Hold a lighted match to the burner, then turn the knob to the LITE position. Use extreme caution when lighting burners this way.

Surface burners in use when an electrical power failure occurs will continue to operate normally.

After Lighting a Burner

•Do not operate a burner for an extended period of time without cookware on the grate. The finish on the grate may chip without cookware to absorb the heat.

•Be sure the burners and grates are cool before you place your hand, a pot holder, cleaning cloths or other materials on them.

How to Select Flame Size

Watch the flame, not the knob, as you reduce heat.

The flame size on a gas burner should match the cookware you are using.

FOR SAFE HANDLING OF COOKWARE NEVER LET THE FLAME EXTEND UP THE SIDES OF THE COOKWARE.

Any flame larger than the bottom of the cookware is wasted and only serves to heat the handle.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation Instructions Save time and money. Before you request service… Help US Help YOU…Read this guide carefully If you received a damaged range…Important Safety Instructions Important Safety InstructionsWhen You Get Your Range For your safety, never use your applianceSurface Cooking Clean only parts listed in this Use and Care Guide Save These InstructionsFeatures of Your Range Features and appearance varyFeatures of Your Range Surface Cooking Do not use a wok on a support ring. Placing Surface CookingTop-of-Range Cookware Features of Your Oven Control Cook Time ON/OFF. Press this for Timed Baking operationsYour Oven Control Oven CONTROL, Clock and TimerOven Control, Clock and Timer Using Your Oven Using Your Oven Oven ShelvesShelf Positions Automatic Oven Shut OffType of Food Shelf Position How to Set Your Range for BakingBaking Oven BakingPies CakesBaking Pans Don’t PeekHow to Time Bake How to Set Immediate Start and Automatic StopTimed Baking Timed BakingHow to Set Delay Start and Automatic Stop Questions and AnswersCan I use the minute timer during oven cooking? Quick ReminderSabbath Feature How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature To Adjust the Thermostat Adjust the Oven ThermostatAdjust the Oven Thermostat Use of Aluminum Foil RoastingDual Shelf Cooking Why is my roast crumbling when I try to carve it? Roasting GuideRoasting Roasting GuideWhy are my meats not turning out as brown as they should? BroilingOven door must be closed during broiling Should I salt the meat before broiling?Broiling Guide Broiling GuideDo not rub or clean the door gasket Operating the SELF-CLEANING OvenBefore a Clean Cycle How to Set the Oven for Cleaning To Stop a Clean CycleAfter a Clean Cycle Clean cycle time is normally 4 hoursHow to Set Delay Start of Cleaning on some models Can I clean the woven gasket around the oven door?Should there be any odor during the cleaning? Why do I have ash left in my oven after cleaning?Care and Cleaning Self-Cleaning Oven CareCleaning OperatingSealed Burner Assemblies on some models For proper ignitionCare and Cleaning Burner GratesCooktop Surface Oven BottomLift-Off Oven Door Broiler Pan and GridInside of the door Outside of the doorRemovable Storage Drawer on some models Oven Light Replacement on some modelsControl Panel and Knobs Stainless Steel Surfaces on some models Oven Air VentsRemovable Kick Panel on some models Installation Instructions For Your SafetyImportant Safety Instructions General Provide Adequate GAS Supply Rigid Pipe Hookup for Models Equipped with Sealed Burners IMPORTANT-Please read carefully Electrical RequirementsExtension Cord Cautions Electric Disconnect Electric Ignition Models Yellow flamesTo remove the oven bottom Leveling the Range ⁄ 8 ″ QUESTIONS? Before YOU Call for SERVICE… Problem Possible CauseBefore You Call for Service Do not WorkFood does not No Matter What Brand GE Service Protection PlusWarranty Registration Department Box Louisville, KY Consumer Product Ownership Registration Model Number Serial NumberWarranty Consumer Support GE Appliances Website

JGBP40, JR EGR3000, EGR3001 specifications

The GE EGR3001, JR EGR3000, and JGBP40 are three innovative industrial equipment models from General Electric, renowned for their efficiency and advanced engineering.

The GE EGR3001 represents a significant advancement in gas turbine technology. This model is designed for optimal performance in combined cycle power plants, where its high efficiency helps to reduce fuel consumption and greenhouse gas emissions. The EGR3001 features an advanced combustor design that facilitates low emissions and enhances fuel flexibility, allowing it to operate on various fuels, including natural gas and liquid fuels. This flexibility is crucial in today's energy markets, where energy source availability may fluctuate.

The EGR3001 is also equipped with sophisticated control systems that provide reliable performance even under varying load conditions. Its modular design simplifies maintenance, allowing for faster service times and lower operational costs. Additionally, the EGR3001's robust construction ensures durability and longevity, making it an excellent investment for power generators.

The JR EGR3000 is another remarkable model in GE's lineup, focusing on integration and performance in industrial settings. This unit combines the features of a gas turbine with superior steam generation capabilities. The JR EGR3000 prides itself on its compact design, which facilitates easy installation without compromising performance. It features advanced aerodynamics and heat recovery systems that maximize output while minimizing fuel consumption.

A key highlight of the JR EGR3000 is its digital twin technology, which allows operators to simulate and analyze performance in real-time. This technology provides valuable insights for maintenance planning and operational efficiency, leading to decreased downtime and optimally managed assets.

The JGBP40 is a unique offering, primarily designed for industrial applications requiring higher efficiency and reliability. It integrates advanced gearbox technology with high-speed turbine operations, facilitating increased torque and power output. The JGBP40 is designed for versatility, able to support various applications across different industries.

Its design incorporates advanced materials to withstand high-stress conditions, thereby increasing operational lifespan. The model also features smart diagnostics and predictive maintenance capabilities, allowing operators to monitor health and performance efficiently. This proactive approach minimizes unplanned outages and enhances overall productivity.

In summary, the GE EGR3001, JR EGR3000, and JGBP40 are testament to General Electric’s commitment to innovation, efficiency, and reliability in industrial equipment. Their advanced features and technologies not only optimize performance but also address modern energy challenges, making them essential assets for electricity producers and industrial users alike.
Top Page Image Contents