GE JBP26WR, JBP26GR Installation Instructions, NUIT3 This appliance must be properly grounded

Page 26

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and carefilly.

IMPORTANT: Save these instructions for the local electrical inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE TO INSTALLER: Leave these instructions with the appliance after installation is completed.

NOTE TO CONSUMER: Keep this Use and Care Guide and Installation Instructions for future use.

NUIT3: This appliance must be properly grounded.

TOOLS YOU WILL NEED

Large blade screwdriver

STEP 1

PREWRE THE OPENING

1%” spacing is recommended from the range to adjacent vertical walls above cooktop surface.

Allow 30” minimum clearance between surface units and bottom of unprotected wood or metal top cabinet, and 15” minimum between countertop and adjacent cabinet bottom.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a min. of 5“ beyond the bottom of the cabinets.

NOT LESS THAN

WIDTH OF RANGE

i,

/

 

Channel lock pliers or small ratchet wrench with 3/16” socket (for leveling range)

ELECTRICAL REQUIREMENTS

CAUTION, FOR PERSONAL SAF131Y:

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION.

This appliance must be supplied with the proper voltage and tiequency, and connected to an

Iu30” -

MIN. 15J

MIN.

//

0

I

I

I

\

 

 

 

 

 

Y MIN.

LOCATE

I OUTLET BOX WITHIN EITHER SHADED AREA

individual, properly grounded branch circuit, protected by a circuit breaker or time delay fuse, as noted on the rating plate.

Wiring must conform to National Electric Codes.

Lf the electric service provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet.

Because range terminals are not accessible after range is in position, flexible service conduit or cord must be used.

INSTALL

OUTLET BOXJ ON EITHER

SIDE OF Q

I

26

..———. .———

 

———.——

 

-—

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Se and Care&Installation Guide Read this book carefully If YOU Need ServiceHelp US Help YOU Important Safety Notice Oven Important Safety InstructionsSelf-Cleaning Oven Surface Cooking UnitsCan cause hot fat to bubble up and over sides Features of Your Range 26,28 ’eature Indew i Nfi all nxiel~ have all featuresExplained 16, 18, 19Surface Cooking How to Set the ControlsHeat Setting Guide Cooking TipsObserve the Following Points in Canning Deep Fat FryingWok Cooking Canning should be done on surface units onlyQuestions and Answers Automatic Timer and ClockTo Set the Clock Minute Timer Can I use the Minute Timer during oven cooking?Oven Interior Shelves Before Using Your OvenOven Controls How to Set Your Range for Baking Using Your OvenAdjusting Oven Thermostat To adjust the thermostat knobTimed Baking How to Set Immediate Start and Automatic StopHow to Set Delay Start and Stop Preheating Pan PlacementOven Shelves Baking PansCakes Baking GuidesPies Aluminum FoilRoasting Frozen RoastsDoneness Why is my roast crumbling when I try to carve it?Roasting Guide Use of Aluminum Foil Why are my meats not turning out as brown as they should?Broiling Questions & AnswersBroiling Guide Slash fatHow to Set Oven for Cleaning Operating the SELF-CLEANING OvenBefore a Clean Cycle Normal cleaning time 3 hoursAfter a Clean Cycle Calrod Surface Units Cooktop SurfaceLift-Up Cooktop on some models Oven Vent Drip PansCooktop Surface Lamp on some models To removeControl Panel and Knobs Broiler Pan and RackGlass Surfaces Oven Lamp Replacement on some modelsMetal Parts Ift-off Oven DoorInstallation Instructions NUIT3 This appliance must be properly groundedStep Preimre for Electrical Connection Installation Instructions Aluminum Wiring Connect length of copper building wire toOven will Problem Solver Wdll Be There Warranty
Top Page Image Contents