GE JBW3-4 warranty Installation Instructions, Step Wire Power Cord Installation

Page 32

INSTALLATION INSTRUCTIONS

STEP 4

3 WIRE POWER CORD INSTALLATION

Remove the 3 wire terminal screws from the connector block. Insert screws through each power cord terminal ring and into the connector block until the screws engage the

nuts. Be certain that the center wire is connected to the center screw of the connector block. Tighten screws securely. Do NOT remove ground strap connection.

CONNECTOR

NEUTK TERM

D

POWER

W_ING: THE NEUTRAL OR GROUND WIRE OF THE POWER CORD MUST BE CONNEC133D TO THE NEUTRAL TERMINAL LOCA’T’ED IN THE CENTER OF THE CONNECTOR BLOCIL THE POWER LEADS MUST BE CONNECTED TO THE OUTSIDE (BRASS COLORED) TERMINALS.

4 WIRE POWER CORD INSTALLATION

A. Remove the 3 screws from the connector block.

B. Remove the grounding screw and strap from the connector block middle location and the screw connection to the frame of the range.

BEFORE

NEUTRAL

TERMINAL

;ROUNDING STRAP ‘ GROUNDING TO RANGE)

C. Insert screws through each power cord terminal ring and into connector block until screw engages nut. Be certain that the center wire is connected to the center screw of the connector block. Tighten screws securely.

D. Attach ground wire to the frame of the range.

AFTER

W-ING: THE NEUTRAL WIRE OF SUPPLY CIRCUIT IS CONNECTED TO THE NEUTRAL TERMINAL LOCATED IN THE CENTER OF THE CONNECTOR BLOCK. THE POWER LEADS MUST BE CONNECTED TO THE OUTSIDE (BRASS COLORED) TERMINALS. THE 4TH GROUNDING LEAD MUST BE CONNECTED TO THE FRAME OF THE RANGE WITH THE GROUNDING SCREW.

(continued next page)

32

Image 32

Contents EEEEl~ If YOU Need Service Save time and money. Before you request serviceHelp US Help YOU Write down the model and serial numbersImportant Safety Instructions AwarningOflly ~e~ain types of glass glasticeramk OvenSurface Cooking Units Save These INSTRUCTIONS5 Radiant Surface UnitsFeatures of Your Range JBS16 JBS18 JBS30 JBS03 JBS03-4 JBS07 JBS17 JBC17HOW does this Cooktop Compare To Your OLD ONE? RadiantGeneral Information About Radiant Surface Units Glass Cooktop Cautions Home Canning TipsObserve the Following Points in Canning Special Notes for Glass Cooktops How to Set the ControlsCooking Guide for Using Heat Settings Hot Surface Indicator Light Glass Cooktops Only Surface ControlsSurface Cookware Tips CookwareWok Cooking ~pes of CookwareHow to Check Pan Performance Glass Cooktop Cleaning Glass Cooktop CleaningClock Before Using Your Oven Oven ControlsOven Shelves Shelf PositionsPreheating How to Set Your Range for BakingBaking Pan Placement Baking PansBaking Guides CookiesAdjust the Oven Thermostat RoastingFrozen Roasts Roasting GuideUse of Aluminum Foil Broiling Questions & AnswersOven door should be open to the broil stop position Care and Cleaning Surface Units and Drip Pans Electric Coil Models Porcelain Enamel Cooktop Electric Coil ModelsTo replace a surface unit To remove a surface unitOven Heating Elements Oven Light Replacement on some modelsBroiler Pan and Grid on some models If necessary, you may use an oven cleaner Lift-Off Oven DoorPorcelain Oven Interior Outside of doorContinuous-cleaning Oven Interior on some models To Clean the Continuous-Cleaning OvenControl Panel and Knobs Painted SurfacesMetal Parts Glass Window on some models and Glass SurfacesInstallation Instructions NXE This appliance must be properly groundedStep Prepare for Electrical Connection Flooring Under the RangeInstallation Instructions Step Wire Power Cord InstallationLhcOND’T Step Final Check Glass Cooktop Models QUESTIONS? USE this Problem Solver131ectric Coil Models Problem Solver Work ProperlyV2 w Page Wdll Be There Warranty