GE JGBP26 A, JGBP85 A, JGBP79 A, JGBP90 A Cook TOP / Surface Burners, To Raise or Remove Cook TOP

Page 12

TO RAISE OR REMOVE COOK TOP

Remove 4 burner caps and 4 burner heads

Remove 4 electrodes (pull up on the electrode while gently rotating at the same time) & disconnect electrode leads.

Remove (12) T-15 torx screws which mount the orifice holders to the cook top

Disengage the 2 front clips using a flat screw driver and gently raise the top high enough for the prop rods to hold it upright.

FOR REMOVAL:

Disengage the prop rods from the range slide panels

While raising the front of the cooktop, lower the rear of the cook top and shift the top left or right in order to disengage the hinge pins at the rear.

IMPORTANT COOK TOP REINSTALLATION NOTES:

Before lowering the top onto the front clips, feed the electrode leads through each opening in the cook top. Next be sure that the electrode clips are inserted into each of the orifice brackets (see illustration below). Line up the orifice brackets with the holes in the cook-top and start the screws, which secure the cook-top to the orifice holders. Before tightening the screws be sure to check the electrode leads to ensure that they do not get pinched between the cook top and the orifice holder. Reconnect the electrode wires and gently push each of the electrodes into position.

When reinstalling the top, position the top to be the equivalent of 1/2 way lowered, before attempting to insert the top hinge pins into the corresponding slots on the back-guard.

GRATE

Flame Stability

COOK TOP / SURFACE BURNERS

COOK TOP RAISED POSITION

COOK TOP REMOVAL

BURNER HEAD

The burner head has a flame stability chamber which protects a small pocket of flame. This small pocket of flame provides quick reignition, in the event of a minor burner flame outage during simmer. It also provides an additional measure of safety.

The burner head also provides a positive target area for the Ignitor.

BURNER

HEAD

IGNITOR

BURNER CAP

Chamber

ELECTRODE MOUNTING

BURNER HEAD

 

 

PAN

SCREWS

ELECTRODE

CLIP

T-15 Torx

Screws

(Compression

 

Sleeve)

 

ORIFICE

Each electrode pushes into a clip (compression sleeve), which mounts to each of the four orifice holders. This allows the electrode to be removed without lifting the

top. To remove the electrode, grasp it with your finger and thumb and pull upward. A slight twisting action may help in removing

the electrode. All four electrodes MUST be removed prior to lifting the top.

 

HOLDER,

 

ORIFICE

COOK TOP

COMPRESSION

NUT

 

TUBE

HOLDER, ORIFICE

To improve alignment and stability the 4 burner orifice brackets (holders) have been modified. The brackets are mounted to the cooktop with three "T-15" torx screws. The screw heads are located under the burner head. These screws MUST be removed prior to lifting the cooktop. The rigid mounting system ensures proper alignment of the orifice for gas to be injected into the burner head.

– 10 –

Image 12
Contents Technical Service Guide Important Safety Notice Table of Contents Featured Model About this Technical Service Guide Featured ModelJGBP85BEA Full Range of Power GE TrueTemp Only GE GAS Ranges have AN Appetite this BIG Weve PUT a NEW Spin on a Grate TOP NEW Features / Design So Whats New?30 XL44 SELF-CLEANING GAS Ranges 30 XL44 Continuous and Standard Clean GAS Ranges Cook TOP / Surface Burners To Raise or Remove Cook TOPLOW Flame Simmer Adjustments Conversion to LP Propane GASBake Burner Adjustments Broil Burner AdjustmentsConversion & Orifices Information Orifice InformationControl Panel Access Reinstalling Control PanelEND CAPERC III Special Features ERCFahrenheit or Centigrade Temperature Helpful USE and Care InformationCook and Hold Changing the Speed of the + or Pads on Some ModelsThermostat Cycling Most Accurate Oven In AmericaERC Fault Code Memory Test ERC Fault Code Memory DisplayHOW to Display the Fault Codes in Memory HOW Fault Codes are Stored in Memory ExampleERC Diagnostic Tests ERC on Board Diagnostic TestsHOW to Enter and Exit the Diagnostic Mode HOW to Perform the TestsLock Motor Access Lock Motor CircuitDoor Latch Mechanism PCB ERC JGBP85BEA Strip Circuits D1 R RK SW O D3 OJGBP85BEA Diagnostic Info Failure Codes F CodesJGBP30BEA Schematic ERT Control VoltagesJGBP30BEA Strip Circuits JGBP85BEA JGBP85BEA JGBP85BEA JGBP85BEA Illustrated Parts Catalog Model JGBP85BEA1BBVent ASM Glow BAR XL44 Gas Ranges