Maytag W10252706B wire connection Direct Wire, A B Cd E, Bare Wire Torque Specifications

Page 11
E. Neutral (white) wire

6.Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

 

G

 

 

B

 

 

 

 

F

 

D

E

C

 

 

 

A. 10–32 hex nut

E. Neutral (white) wire

B. Line 2 (red)

F. Line 1 (black)

C. Bare (green) ground wire

G. Terminal lug

D.Ground-link screw

7.Connect line 2 (red) and line 1 (black) wires to the outer terminal block posts with 10-32 hex nuts.

8.Securely tighten hex nuts.

9.Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground conductor to neutral supply wire.

1.Pull the wires through the conduit on cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A G. Terminal lug3-wire connection: Direct WireAD. Bare (green) ground wireManual backgroundManual backgroundManual backgroundManual background

 

 

 

B

 

 

 

C

 

 

 

F

D

E

 

 

A. Terminal block

 

D. Line 2

(red) wire

B. Ground-link screw

E. Bare (green) ground wire

C. Cord/conduit plate

F. Line 1

(black) wire

2.Attach terminal lugs to line 2 (red), bare (green) ground, and line 1 (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart.

A

Manual backgroundManual backgroundB

CD E

A. Terminal lug

B.Setscrew

C.Line 2 (red) wire

D.Bare (green) ground wire

E.Line 1 (black) wire

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Wire Awg

Torque

8 gauge copper

25 lbs-in. (2.8 N-m)

 

 

6 gauge aluminum

35 lbs-in. (4.0 N-m)

 

 

3.Use ³⁄₈" nut driver to connect the bare (green) ground wire to the center terminal block post with one of the 10–32 hex nuts.

F

A

E

B

 

D

 

C

A. 10–32 hex nut

D. Bare (green) ground wire

B. Line 2 (red)

E. Line 1 (black)

C. Ground-link screw

F. Terminal lug

4.Connect line 2 (red) and line 1 (black) wires to the outer terminal block posts with 10-32 hex nuts.

5.Securely tighten hex nuts.

6.Replace terminal block access cover.

11

Image 11
Contents Table of Contents W10252706BINSTALLATION INSTRUCTIONS 30 76 CM FREESTANDING ELECTRIC RANGES DANGER RANGE SAFETYYour safety and the safety of others are very important Location Requirements INSTALLATION REQUIREMENTSMobile Home - Additional Installation Requirements Tools and PartsA C B D E Product DimensionsCabinet Dimensions Electrical Requirements - U.S.A. OnlyElectrical Connection If connecting to a 4-wire systemIf connecting to a 3-wire system A D C B INSTALLATION INSTRUCTIONSInstall Anti-Tip Bracket Unpack RangeElectrical Connection - U.S.A. Only Power Supply CordDirect Wire connecting to 4-wire connection Power Supply CordStyle 1 Power supply cord strain relief Style 2 Direct wire strain reliefD. Neutral white wire 3-wire connection Power Supply CordA B C D E. Neutral center wireA B CDE Direct Wire Installation Copper or Aluminum Wire4-wire Connection Direct Wire Bare Wire Torque SpecificationsE. Neutral white wire 3-wire connection Direct WireA B CD E D. Bare green ground wireTo Remove Verify Anti-Tip Bracket LocationLevel Range Storage DrawerTo Replace Complete InstallationMoving the Range For power supply cord-connected rangesFor direct-wired ranges Top edge Left edge ANTI-TIP BRACKET TEMPLATEAll rights reserved W10252706B2009 9/09