Brinkmann 816-3500 SERIES How To Reignite Burner, Burner Flame Check, Turning Off The Fryer

Page 11
HOW TO REIGNITE BURNER:

4.Insert paper match in match holder prior to striking. Strike and place match through lighting hole to approximately 1/2" (2 to 3 cm) from the burner. We recommend the use of a long wooden match.

5.Slowly turn regulator control knob clockwise until burner lights.

6.If burner does NOT ignite immediately, turn the regulator control knob and cylinder valve to OFF, wait 5 minutes for gas to evacuate and repeat steps 1 through 4 until burner ignites.

7.If the burner does not light within the first few attempts, there is a problem with the gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the fryer until the problem is found and corrected.

HOW TO REIGNITE BURNER:

It is recommended to place lid over cooking vessel before reigniting burner. Follow steps 1 through 4 above, to reignite burner. Use caution when lighting burner, hot oil from cooking vessel may have splattered and run down the sides of the unit.

BURNER FLAME CHECK

Adjust flame height using regulator control knob. Rotate air shutter to achieve mostly blue flame. The air damper mounted on the back of your burner helps to control the amount of air that mixes with the LP gas. A blue flame with little or no yellow flame provides the

best heat. Adjust the air damper until the desired flame is achieved.

Air Hole

Rotating

 

Air Shutter

Yellow

Blue

2”

1”

0”

Burner Hole

BURNER FLAME CHECKRegulator Control Knob

Match Holder

Lighter Hole

NOTE: Make sure the male fitting on the fryer is screwed into the air shutter and tightened securely. Do not over-tighten as the air shutter needs to move freely in order to adjust air intake. Check the attachment for proper connection every time propane tank is connected to fryer.

TURNING OFF THE FRYER:

1. Turn OFF the LP cylinder valve.

2. Turn regulator control knob to the OFF position.

NOTE: Turn off LP cylinder first to prevent gas from being left in the system under pressure.

3.To disconnect valve regulator/hose assembly, turn the large regulator coupling counter-clockwise by hand.

2” CAUTION!

• The LP cylinder valve should always be in the OFF or closed position when the fryer is not in use.

To turn off the LP cylinder valve, turn knob clockwise until it stops.

10

Image 11
Contents READ THIS MANUAL ASSEMBLY AND OPERATING INSTRUCTIONSKEEP THIS MANUAL FOR FUTURE REFERENCE This appliance can produce carbon monoxide which has no odor DANGERUsing it in an enclosed space can kill you CARBON MONOXIDE HAZARDDo NOT install or use in or on recreational vehicles and/or boats Do NOT use lid when heating or cooking with oilDO NOT use external electrical sources with this appliance CYLINDER SPECIFICATIONS INSTALLATION INFORMATIONFILLING THE LP GAS CYLINDER HOSE AND REGULATOR WHEN TO PERFORM A LEAK TEST CONNECTING HOSE AND REGULATOR TO AN LP GAS CYLINDERLEAK TESTING C Back side of connection nut to brass nipple GAS LEAK TESTINGF Gas supply hose connection to burner assembly A Supply tank cylinder weld B Connection nut to cylinder valve12 ft PRE-START CHECK LISTLIGHTING INSTRUCTIONS 10 ft2” 1” 0” HOW TO REIGNITE BURNERBURNER FLAME CHECK TURNING OFF THE FRYEROPERATING INSTRUCTIONS HOW TO DETERMINE PROPER AMOUNT OF OILFor Use With Cooking Vessels That Do Not Have Maximum Fill Line Pan & Basket Turkey Stand7” Strainer 14” StrainerNOTE Wear eye protection when cleaning burner BURNER ASSEMBLY/MAINTENANCECLEANING & GENERAL MAINTENANCE Proof of purchase will be required ASSEMBLY INSTRUCTIONSFOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT PROCEED TO “GAS LEAK TESTING” SECTION ON PAGE2003 The Brinkmann Corporation Dallas, Texas 75244 U.S.A 90 DAY LIMITED WARRANTYONE YEAR LIMITED WARRANTY