Sharp R-216LS service manual Servicing Tools, Other Precautions

Page 22

R216LS

2)Open the door and block it open.

3)Discharge high voltage capacitor.

4)Disconnect the leads to the primary of the power transformer.

5)Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.

6)After that procedure, re-connect the power supply cord.

After checking the performance of the touch control panel,

1)Disconnect the power supply cord.

2)Open the door and block it open.

3)Re-connect the leads to the primary of the power transformer.

4)Re-install the outer case (cabinet).

5)Re-connect the power supply cord after the outer case is installed.

6)Run the oven and check all functions.

a)On some models, the power supply cord between the touch control panel and the oven itself is so short that the two can't be separated. For those models, check and repair all the controls (sensor-related ones included) of the touch control panel while keeping it connected to the oven.

b)On some models, the power supply cord between the touch control panel and the oven proper is so long enough that they may be sepa- rated from each other. For those models, therefore, it is possible to check and repair the controls of the touch control panel while keeping it apart from the oven proper; in this case you must short both ends of the door sensing switch (on PWB) of the touch control panel with a jumper, which brings about an operational state that is equivalent to the oven door being closed. As for the sensor-related controls of the touch control panel, checking them is possible if the dummy resistor(s) with resistance equal to that of the controls are used.

2.Servicing the touch control panel with power supply from an external power source:

Disconnect the touch control panel completely from the oven proper, and short both ends of the door sensing switch (on PWB) of the touch control panel, which brings about an operational state that is equivalent to the oven door being closed. Connect an external power source to the power input terminal of the touch control panel, then it is possible to check and repair the controls of the touch control panel; it is also possible to check the sensor-related controls of the touch control panel by using the dummy resistor(s).

3.Servicing Tools

Tools required to service the touch control panel assembly.

1)Soldering iron: 60W

(It is recommended to use a soldering iron with a grounding terminal.)

2)Oscilloscope: Single beam, frequency range: DC - 10MHz type or more advanced model.

3)Others: Hand tools

4. Other Precautions

1)Before turning on the power source of the control unit, remove the aluminium foil applied for preventing static electricity.

2)Connect the connector of the key unit to the control unit being sure that the lead wires are not twisted.

3)After aluminium foil is removed, be careful that abnormal voltage due to static electricity etc. is not applied to the input or output terminals.

4)Attach connectors, electrolytic capacitors, etc. to PWB, making sure that all connections are tight.

5)Be sure to use specified components where high precision is required.

9 – 2

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model R-216LS Adjustment Procedure Precautions for Using Lead Free SolderComponent Replacement Microwave Measurement PROBefore Servicing After repairing When the testing is completedBefore Servicing Requirements Microwave Measurement ProcedurePreparation for testing Leakage testForeword and Warning ForewordProduct Description 1 Specifications DescriptionGrounding Instructions Oven DiagramGeneral Information OvenTouch Control Panel Description of Operating Sequence Power Level CookingPower Output Reduction OFF ConditionOff Condition Schematic Door Closed Clock Appears on DisplayOven Schenatic Cooking ConditionDescription and Function of Components Troubleshooting Guide Troubleshooting ChartProcedure B Power Transformer Test Test ProceduresProcedure a Magnetron Assembly Test Procedure C High Voltage Rectifier TestProcedure F Secondary Interlock Switch Test Procedure D High Voltage Capacitor TestProcedure E Temperature Fuse Oven Test Procedure F Primary Interlock System TestProcedure H Blown Minitor Fuse Test Procedure G Monitor Switch TestPrimary Interlock Relay RY2 Key Unit Procedure I Noise Filter TestProcedure J Touch Control Panel Assembly Test Control UnitProcedure K KEY Unit Test Procedure L Relay TestProcedure M Defrost Test Procedure N Foil Pattern on the Printed Wiring Board TestR216LS Outline of Touch Control Panel Touch Control Panel AssemblyPrecautions for Handling Electronic Components Servicing for Touch Control PanelOther Precautions Servicing ToolsEmploying lead-free solder Precautions for Using LEAD-FREE SolderUsing lead-free wire solder SolderingComponent Replacement and Adjustment PROCE- Dure Outer Case RemovalReinstall Power Transformer RemovalPositive Lock Connector NO-CASE Type Removal Magnetron RemovalGraphic Sheet and Membrane Switch Replacement Control Panel Assembly RemovalTrol Panel Assembly Removal Turntable Motor Removal Power Supply Cord ReplacementCooling FAN Motor Removal Make Sure That the FAN Blade Rotates Smooth After Installed InstallationAdjustment Make Sure That the Axis of the Shaft is not SlantedAfter adjustment, check the following Door ReplacementAfter any service, make sure of the following Figure C-7. Door Replacement Sealer FilmDiagrams Pictorial Diagram FigureControl Panel Circuit Figure S-2 Liquid Crystal DisplayUnit Printed Wiring Board Figure S-3DIP CodeMeno Parts Guide Oven Parts Oven Parts Parts Code Price NEW Description Rank MarkDoor and Control Panel Parts Door and Control Panel Parts „INDEX

R-216LS specifications

The Sharp R-216LS is a versatile microwave oven that combines affordability with a range of features designed to enhance your cooking experience. Compact yet powerful, this model is especially suitable for small kitchens or dorm rooms, where space is at a premium.

One of the standout features of the Sharp R-216LS is its impressive 800 watts of cooking power. This ensures quick and efficient heating, allowing users to prepare meals in a fraction of the time compared to conventional ovens. The microwave also features a variety of power levels, providing flexibility for different types of cooking and reheating tasks, from defrosting frozen food to cooking delicate items like baked goods.

The R-216LS comes equipped with a spacious 20-liter capacity, which is surprisingly roomy for its size. This allows for ample space to heat up large dishes or multiple servings at once. The interior is designed with easy cleaning in mind, featuring a non-stick coating that prevents food from adhering to the surfaces and simplifies maintenance.

In terms of usability, the Sharp R-216LS boasts a user-friendly interface with straightforward knobs and buttons. It includes a timer and a range of pre-programmed cooking options, enabling users to cook a variety of foods with just the touch of a button. This is particularly beneficial for those new to microwave cooking or for busy individuals looking to save time.

The microwave also incorporates advanced technologies, including inverter microwave technology, which provides a continuous stream of cooking power for more even heating and defrosting. This ensures that your food is cooked thoroughly without the risk of hot and cold spots.

Safety is another priority in the design of the R-216LS. It features a child safety lock, which prevents accidental operation, making it a perfect choice for families with young children. The model also has an automatic shut-off feature, ensuring that the microwave turns off when not in use.

In summary, the Sharp R-216LS is a compact microwave that offers a blend of power, convenience, and safety features, making it an excellent choice for anyone seeking a reliable cooking appliance. Whether for reheating leftovers, cooking meals, or defrosting ingredients, this microwave is designed to meet the diverse needs of modern kitchens. With its combination of thoughtful design and functionality, the R-216LS stands out as a worthy investment for those looking for efficiency and performance in their cooking appliances.
Top Page Image Contents