Sharp R-216LS service manual Product Description 1 Specifications

Page 7

R216LS

CHAPTER 4. PRODUCT DESCRIPTION [1] SPECIFICATIONS

ITEM

DESCRIPTION

 

 

120 Volts

 

Power Requirements

60 Hertz

 

 

Single phase, 3 wire grounded

Power Consumption

1170W / Approx. 10 Amperes

Power Output

800 W nominal of RF microwave energy (IEC Test procedure)

Operating frequency 2450 MHz

 

 

Width

18-1/8" (460mm)

 

Case Dimensions

Height 10-7/8" (275mm)

 

 

Depth 14-5/8" (370mm)

 

Cooking Cavity Dimensions

Width

12-1/2" (319mm)

NOTE: Internal capacity is calculated by measuring

Height

8" (204mm)

maximum width, depth and height.

(0.8 Cubic feet)

Depth

13-1/4" (336mm)

Actual capacity for holding food is less.

 

 

Touch Control System

 

 

Clock (1:00 - 12:59)

 

 

Timer (0 - 99 minutes 99 seconds)

 

Microwave Power for Variable Cooking

 

Repetition Rate;

 

 

P-HI ---------------------

Full power throughout the cooking time

Control Complement

P-90 --------------------

approx. 90% of FULL Power

P-80

approx. 80% of FULL Power

 

 

P-70 --------------------

approx. 70% of FULL Power

 

P-60 --------------------

approx. 60% of FULL Power

 

P-50 --------------------

approx. 50% of FULL Power

 

P-40 --------------------

approx. 30% of FULL Power

 

P-30 --------------------

approx. 40% of FULL Power

 

P-20 --------------------

approx. 20% of FULL Power

 

P-10 --------------------

approx. 10% of FULL Power

 

P-0 ----------------------

No power throughout the cooking time

 

POPCORN pad

 

 

SHORT CUTS pads

 

 

REHEAT pad

 

 

COOK pad

 

 

DEFROST pad

 

 

Number selection pads

 

 

TIMER / CLOCK pad

 

 

POWER LEVEL pad

 

 

START/MINUTE PLUS pad

 

STOP/CLEAR pad

 

Oven Cavity Light

Yes

 

 

 

UL Listed.

 

Safety Standard

FCC Authorized

 

 

DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J

4 – 1

Image 7
Contents Model R-216LS Microwave Measurement PRO Precautions for Using Lead Free SolderComponent Replacement Adjustment ProcedureBefore Servicing After repairing When the testing is completed Before Servicing Leakage test Microwave Measurement ProcedurePreparation for testing RequirementsForeword Foreword and WarningDescription Product Description 1 SpecificationsOven Oven DiagramGeneral Information Grounding InstructionsTouch Control Panel OFF Condition Power Level CookingPower Output Reduction Description of Operating SequenceCooking Condition Schematic Door Closed Clock Appears on DisplayOven Schenatic Off ConditionDescription and Function of Components Troubleshooting Chart Troubleshooting GuideProcedure C High Voltage Rectifier Test Test ProceduresProcedure a Magnetron Assembly Test Procedure B Power Transformer TestProcedure F Primary Interlock System Test Procedure D High Voltage Capacitor TestProcedure E Temperature Fuse Oven Test Procedure F Secondary Interlock Switch TestProcedure H Blown Minitor Fuse Test Procedure G Monitor Switch TestPrimary Interlock Relay RY2 Control Unit Procedure I Noise Filter TestProcedure J Touch Control Panel Assembly Test Key UnitProcedure L Relay Test Procedure K KEY Unit TestProcedure N Foil Pattern on the Printed Wiring Board Test Procedure M Defrost TestR216LS Servicing for Touch Control Panel Touch Control Panel AssemblyPrecautions for Handling Electronic Components Outline of Touch Control PanelServicing Tools Other PrecautionsSoldering Precautions for Using LEAD-FREE SolderUsing lead-free wire solder Employing lead-free solderOuter Case Removal Component Replacement and Adjustment PROCE- DureMagnetron Removal Power Transformer RemovalPositive Lock Connector NO-CASE Type Removal ReinstallGraphic Sheet and Membrane Switch Replacement Control Panel Assembly RemovalTrol Panel Assembly Removal Turntable Motor Removal Power Supply Cord ReplacementCooling FAN Motor Removal Make Sure That the Axis of the Shaft is not Slanted InstallationAdjustment Make Sure That the FAN Blade Rotates Smooth After InstalledAfter adjustment, check the following Door ReplacementAfter any service, make sure of the following Sealer Film Figure C-7. Door ReplacementPictorial Diagram Figure DiagramsLiquid Crystal Display Control Panel Circuit Figure S-2Code Printed Wiring Board Figure S-3DIP UnitMeno Parts Guide Oven Parts Parts Code Price NEW Description Rank Mark Oven PartsDoor and Control Panel Parts Door and Control Panel Parts „INDEX