Sharp R-216LS Installation, Adjustment, Make Sure That the Axis of the Shaft is not Slanted

Page 28

R216LS

8.Remove the fan blade assembly from the shaft of the fan motor by pulling and rotating the fan blade with your hand.

9.Now, the fan blade will be free.

CAUTION: DO NOT RE-USE THE REMOVED FAN BLADE BECAUSE THE HOLE (FOR SHAFT) MAY BE LARGER THAN NORMAL.

10.Now, the fan motor is free.

3.Apply the screw lock tight into the hole (for shaft) of the fan blade.

4.Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet.

CAUTION: DO NOT HIT THE FAN BLADE STRONGLY WHEN INSTALLED BECAUSE THE BRACKET MAY BE TRANS- FORMED.

MAKE SURE THAT THE FAN BLADE ROTATES SMOOTH AFTER INSTALLED.

2. INSTALLATION

1.Install the fan blade to the fan motor shaft according to the following procedure.

2.Hold the center of the bracket which supports the shaft of the fan motor on the flat table.

MAKE SURE THAT THE AXIS OF THE SHAFT IS NOT SLANTED.

5.Install the fan motor assembly to the oven cavity back plate with two (2) screws.

6.Connect the wire leads to the magnetron and fan motor, referring to the pictorial diagram.

Coil

 

 

 

Groove joint pliers

 

 

Shaft

Stator

 

Axis

 

Stator

Gap

 

 

Rotor

Bracket

Rotor

Side View

 

Rear View

These are the positions

 

that should be pinched

 

with pliers.

Table

 

Shaft

Center of bracket

[12]DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL

1. REMOVAL

1.Disconnect the power supply cord and remove outer case.

2.Open the door and block it open.

3.Discharge high voltage capacitor.

4.Remove the control panel assembly, referring to section of CON-

TROL PANEL ASSEMBLY REMOVAL.

5.Remove the switch lever from the oven cavity.

6.Disconnect wire leads from the switches.

7.Remove two (2) screws holding latch hook to oven flange.

8.Remove latch hook assembly from oven flange.

9.Push outward on the two (2) retaining tabs holding switch in place. 10.Switch is now free.

2. REINSTALL

1.Re-install each switch in its place. The secondary interlock/monitor switches are in the lower position and the door sensing switch is in the upper position.

2.Secure latch hook (with two (2) mounting screws) to oven flange.

3.Re-connect wire leads to each switch. Refer to pictorial diagram.

4.Install the switch lever to the oven cavity.

5.Reinstall the control panel assembly to the oven cavity.

6.Reconnect wire leads to the control unity, referring to the pictorial diagram.

7.Make sure that the monitor switch is operating properly and check continuity of the monitor circuit. Refer to chapter "Test Procedure" and Adjustment procedure.

[13]DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT

1. Adjustment

1.Disconnect the power supply cord, and then remove outer case.

2.Open the door and block it open.

3.Discharge high voltage capacitor.

If the door sensing switch, secondary interlock switch and monitor switch do not operate properly due to a misadjustment, the following adjustment should be made.

4.Loosen the two (2) screws holding latch hook to the oven cavity front flange.

5.With door closed, adjust latch hook by moving it back and forth, and up and down. In and out play of the door allowed by the upper and lower position of the latch hook should be less than 0.5mm. The vertical position of the latch hook should be adjusted so that the door sensing switch and secondary interlock switch are acti- vated with the door closed. The horizontal position of the latch hook should be adjusted so that the plunger of the monitor switch is pressed with the door closed.

6.Secure the screws with washers firmly.

7.Check the operation of all switches. If each switch has not activated with the door closed, loosen screw and adjust the latch hook posi- tion.

11 – 5

Image 28
Contents Model R-216LS Precautions for Using Lead Free Solder Component ReplacementAdjustment Procedure Microwave Measurement PROBefore Servicing After repairing When the testing is completedBefore Servicing Microwave Measurement Procedure Preparation for testingRequirements Leakage testForeword and Warning ForewordProduct Description 1 Specifications DescriptionOven Diagram General InformationGrounding Instructions OvenTouch Control Panel Power Level Cooking Power Output ReductionDescription of Operating Sequence OFF ConditionSchematic Door Closed Clock Appears on Display Oven SchenaticOff Condition Cooking ConditionDescription and Function of Components Troubleshooting Guide Troubleshooting ChartTest Procedures Procedure a Magnetron Assembly TestProcedure B Power Transformer Test Procedure C High Voltage Rectifier TestProcedure D High Voltage Capacitor Test Procedure E Temperature Fuse Oven TestProcedure F Secondary Interlock Switch Test Procedure F Primary Interlock System TestProcedure H Blown Minitor Fuse Test Procedure G Monitor Switch TestPrimary Interlock Relay RY2 Procedure I Noise Filter Test Procedure J Touch Control Panel Assembly TestKey Unit Control UnitProcedure K KEY Unit Test Procedure L Relay TestProcedure M Defrost Test Procedure N Foil Pattern on the Printed Wiring Board TestR216LS Touch Control Panel Assembly Precautions for Handling Electronic ComponentsOutline of Touch Control Panel Servicing for Touch Control PanelOther Precautions Servicing ToolsPrecautions for Using LEAD-FREE Solder Using lead-free wire solderEmploying lead-free solder SolderingComponent Replacement and Adjustment PROCE- Dure Outer Case RemovalPower Transformer Removal Positive Lock Connector NO-CASE Type RemovalReinstall Magnetron RemovalGraphic Sheet and Membrane Switch Replacement Control Panel Assembly RemovalTrol Panel Assembly Removal Turntable Motor Removal Power Supply Cord ReplacementCooling FAN Motor Removal Installation AdjustmentMake Sure That the FAN Blade Rotates Smooth After Installed Make Sure That the Axis of the Shaft is not SlantedAfter adjustment, check the following Door ReplacementAfter any service, make sure of the following Figure C-7. Door Replacement Sealer FilmDiagrams Pictorial Diagram FigureControl Panel Circuit Figure S-2 Liquid Crystal DisplayPrinted Wiring Board Figure S-3 DIPUnit CodeMeno Parts Guide Oven Parts Oven Parts Parts Code Price NEW Description Rank MarkDoor and Control Panel Parts Door and Control Panel Parts „INDEX

R-216LS specifications

The Sharp R-216LS is a versatile microwave oven that combines affordability with a range of features designed to enhance your cooking experience. Compact yet powerful, this model is especially suitable for small kitchens or dorm rooms, where space is at a premium.

One of the standout features of the Sharp R-216LS is its impressive 800 watts of cooking power. This ensures quick and efficient heating, allowing users to prepare meals in a fraction of the time compared to conventional ovens. The microwave also features a variety of power levels, providing flexibility for different types of cooking and reheating tasks, from defrosting frozen food to cooking delicate items like baked goods.

The R-216LS comes equipped with a spacious 20-liter capacity, which is surprisingly roomy for its size. This allows for ample space to heat up large dishes or multiple servings at once. The interior is designed with easy cleaning in mind, featuring a non-stick coating that prevents food from adhering to the surfaces and simplifies maintenance.

In terms of usability, the Sharp R-216LS boasts a user-friendly interface with straightforward knobs and buttons. It includes a timer and a range of pre-programmed cooking options, enabling users to cook a variety of foods with just the touch of a button. This is particularly beneficial for those new to microwave cooking or for busy individuals looking to save time.

The microwave also incorporates advanced technologies, including inverter microwave technology, which provides a continuous stream of cooking power for more even heating and defrosting. This ensures that your food is cooked thoroughly without the risk of hot and cold spots.

Safety is another priority in the design of the R-216LS. It features a child safety lock, which prevents accidental operation, making it a perfect choice for families with young children. The model also has an automatic shut-off feature, ensuring that the microwave turns off when not in use.

In summary, the Sharp R-216LS is a compact microwave that offers a blend of power, convenience, and safety features, making it an excellent choice for anyone seeking a reliable cooking appliance. Whether for reheating leftovers, cooking meals, or defrosting ingredients, this microwave is designed to meet the diverse needs of modern kitchens. With its combination of thoughtful design and functionality, the R-216LS stands out as a worthy investment for those looking for efficiency and performance in their cooking appliances.