Rotel RSX-1067 Controlling Zone 2 from the Main Room, Controlling Zone 2 from the Remote Location

Page 29

29

English

Controlling Zone 2 from the Main Room

You can control Zone 2 from the main room using front panel or remote control buttons to activate or deactivate Zone 2, change input sources, and adjust the volume. Controlling Zone 2 from the main room is accomplished by pressing the ZONE button on the front panel or remote, putting the RSX-1067 in Zone 2 con- trol mode temporarily. When the Zone 2 sta- tus is displayed, the OSD and/or front panel displays show the current source selection and volume in Zone 2 for ten seconds, during which time you can use the front panel VOLUME control and INPUT buttons to change the ZONE 2 settings.

To turn Zone 2 on or off:

1.Press the front panel or remote ZONE but- ton. Zone 2 status appears in the OSD and front panel displays.

2.Within 10 seconds, press the front panel or remote ZONE button to toggle Zone 2 on or off.

3.Following 10 seconds with no commands, the RSX-1067 reverts to normal operation.

To change the Zone 2 input source:

1.Press the front panel or remote ZONE but- ton. Zone 2 status appears in the OSD and front panel displays.

2.Within 10 seconds, press one of the IN- PUT buttons to select a new source for Zone 2. The name of the selected source appears in the display. Instead of pressing an IN- PUT button, you can also push the +/– buttons on the remote to step through the inputs.

3.Following 10 seconds with no commands, the RSX-1067 reverts to normal operation.

To change the Zone 2 volume:

1.Press the front panel or remote ZONE but- ton. Zone 2 status appears in the OSD and front panel displays.

2.Within 10 seconds, adjust the volume control on the front panel or remote to change the Zone 2 output level. The new setting appears in the display.

3.Following 10 seconds with no commands, the RSX-1067 reverts to normal operation.

Controlling Zone 2 from the Remote Location

With a properly configured IR repeater sys- tem, you have full control of Zone 2 using an RR-1050 remote from the Zone 2 location. You can select and operate a source, adjust the volume, and turn Zone 2 on or off. Whatever commands you send from the RR-1050 will change Zone 2 and only Zone 2, just as if you were controlling a totally independent audio system in that room. These changes will have no effect on the main listening room.

To turn Zone 2 on or off, press the ON/OFF buttons on the remote. To adjust the volume in Zone 2, press the VOLUME buttons on the remote. To select a different analog input source, press one of the DEVICE/INPUT buttons on the remote. You can also use the +/– buttons to step through the source inputs.

NOTE: The volume adjustment is only avail- able if the Zone 2 outputs are configured to use VARIABLE levels. With FIXED levels, the volume control for Zone 2 is disabled.

SETUP

The RSX-1067 features two types of informa- tion displays to help operate the system. The first consists of simple status displays that appear on the TV screen and/or front panel display whenever primary settings (Volume, Input, etc.) are changed. These status displays are self- explanatory.

A more comprehensive ON-SCREEN DISPLAY (OSD) menu system is available at any time by pressing the MENU/OSD button on the remote. These OSD menus guide you through the configuration and setup of the RSX-1067. In general, the settings made in the configu- ration process are memorized as default set- tings and need not be made again for nor- mal operation of the unit.

The OSD menus can be configured to display several different languages. The default English version of all the menus is shown at the front of this manual. If your language is available, those menus will be shown in the following instructions. If you would like to change from the default English language before proceed- ing, go to the instructions for the OTHER OP- TIONS menu later in this manual. From this menu, you can change the language display.

Page 28 Page 30
Image 29
Page 28 Page 30
Contents RSX-1067 Page Consult your authorized Rotel retailer for assistance Important Safety InstructionsFCC Information Controls and Connections RSX-1067Surround Sound ReceiverRR-1050 Remote EnglishHF CONTOUR+5 LF Contour Main Menu On-Screen MenusContents Specifications Other SettingsZone 2 Operation Menu BasicsPlacement Key FeaturesAbout Rotel Getting StartedTape Inputs CD InputsTape Outputs Video 1-5 Audio InputsPreamp Outputs Speaker OutputsZone 2 Audio Outputs Composite Video InputsOther Connections Digital Audio Input & OutputsMaking Connections Audio Recorder Cable, Satellite, or Hdtv TunerVCR or Digital Video Recorder DVD-A or Sacd PlayerAmplifiers Connecting a SubwooferAM Antenna FM AntennaFront-panel Display Using the RR-1050 Audio ButtonRemote Sensor Programming the RR-1050 Preload ButtonVolume Knob Volume Button Standby Button Power ButtonSurround Mode Buttons ON/OFF ButtonsSelecting Inputs Basic OperationsSelecting a Source Input from the Front Panel Overview Surround FormatsSelecting a Source from the Remote Selecting Digital InputsDTS DTS 96/24 Dolby DigitalDTS Neo6 Dolby Digital Surround EXRotel XS 7.1 Channel Surround Dolby Pro Logic 7.1 Channel SurroundDSP Music Modes 2Ch/5Ch/7Ch Stereo FormatsDolby Digital 5.1 discs Dolby Digital Surround EX discs ModesManually Selecting Surround Modes Mpeg Multichannel discs Dolby Digital 2.0 discsDTS 5.1 discs DTS 96/24 discs DTS-ES 6.1 discs Analog Stereo Digital Stereo discs PCM, MP3, and HdcdGroup Delay Other SettingsContour/Tone Settings Speaker LevelNormal Frequency tuning Numeric Buttons Station PresetsTuner Controls Cinema EQRDS and Rbds Tuning Zone 2 Operation Controlling Zone 2 from the Main Room To change the Zone 2 volumeControlling Zone 2 from the Remote Location To turn Zone 2 on or offMenu Basics Configuring InputsEnglish Buttons to change the selected parameter as follows Multi Input Setup Dolby Pro Logic IIUnderstanding Speaker Configuration ConfiguringSpeaker Setup Center Speakers large/smallSpeakers to be configured with custom settings Advance Speaker SetupSurround Speakers large/small Center Back Speakers large1Crossover 40Hz/60Hz/80Hz/ 100Hz/120Hz/150Hz/200Hz/OFF Subwoofer SetupTest Tone Contour Setup Delay SetupCalibration with an SPL meter Speaker front/center/surround/cenOther Options Zone 2 SetupTo change the Front Redirect setting Default SetupTo memorize User Default settings To activate memorized User DefaultTroubleshooting Specifications Rotel Deutschland Rotel of AmericaRotel Europe
Top Page Image Contents