Rotel RSX-1067 owner manual Important Safety Instructions, FCC Information

Page 3

Notice

The COMPUTER I/O connection should be handled by authorized person only.

FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radi- ate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communica- tions.

However, there is no guarantee that interference will not occur in a particu- lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.(TV, radio, etc.)

Increase the separation between the equipment and receiver

Connect the equipment to an outlet on circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for additional help.

Caution

This device complies with part 15 of the FCC Rules operation is subject to the following to conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE TO CATV SYSTEM INSTALLER: Call the CATV system or antenna installer’s attention to Article 820-40 of the NEC. This provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. See installation diagram.

NOTE: This equipment has been tested and found to comply with the lim- its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates and can radiate ra- dio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio or TV communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, try to cor- rect the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the unit and the television tuner.

Connect the unit to an AC power outlet on a different electrical circuit.

Consult your authorized Rotel retailer for assistance.

Important Safety Instructions

WARNING: There are no user serviceable parts inside. Refer all servic- ing to qualified service personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do not allow foreign objects to get into the enclo- sure. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs.

Read all the instructions before connecting or operating the component.

Keep this manual so you can refer to these safety instructions.

Heed all warnings and safety information in these instructions and on the product itself. Follow all operating instructions.

Clean the enclosure only with a dry cloth or a vacuum cleaner.

Do not use this unit near water.

You must allow a minimum of 10 cm or 4 inches of unobstructed clearance around the unit. Do not place the unit on a bed, sofa, rug, or similar sur- face that could block the ventilation openings. If the unit is placed in a bookcase or cabinet, there must be ventilation of the cabinet to allow proper cooling.

Keep the component away from radiators, heat registers, stoves, or any other appliance that produces heat.

The unit must be connected to a power supply only of the type and voltage specified on the rear panel. (USA: 115 V/60Hz, EC: 230V/50Hz)

Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent. Do not modify the supplied cable. Do not A polarized plug has two blades, with one wider than the other. A grounding plug has two blades plus a third grounding prong. These are provided for your safety. Do not defeat grounding and/or polarization safety provisions. If the supplied plug does not fit your outlet, please consult an electrician for replacement of the obsolete outlet. Do not use extension cords.

The main plug of the power cordset is a disconnect device of the appara- tus. In order to completely disconnect the apparatus from the supply mains, the main plug of the power cordset should be unplugged from the mains (AC) outlet. The stand-by LED indicator will not be lit up to show the power cord is unplugged.

Do not route the power cord where it will be crushed, pinched, bent, ex- posed to heat, or damaged in any way. Pay particular attention to the power cord at the plug and where the cord exits the back of the unit.

The power cord should be unplugged from the wall outlet during a light- ning storm or if the unit is to be left unused for a long period of time.

Use only accessories specified by the manufacturer.

Use only with a cart, stand, rack, bracket or shelf system recommended by Rotel. Use caution when moving the unit in a stand or rack to avoid injury from a tip-over.

Immediately stop using the component and have it inspected and/or ser- viced by a qualified service agency if:

The power supply cord or plug has been damaged.

Objects have fallen or liquid has been spilled into the unit.

The unit has been exposed to rain.

The unit shows signs of improper operation

The unit has been dropped or damaged in any way

Image 3
Contents RSX-1067 Page Important Safety Instructions FCC InformationConsult your authorized Rotel retailer for assistance Controls and Connections RSX-1067Surround Sound ReceiverRR-1050 Remote EnglishHF CONTOUR+5 LF Contour Main Menu On-Screen MenusContents Menu Basics Other SettingsSpecifications Zone 2 OperationGetting Started Key FeaturesPlacement About RotelVideo 1-5 Audio Inputs CD InputsTape Inputs Tape OutputsComposite Video Inputs Speaker OutputsPreamp Outputs Zone 2 Audio OutputsOther Connections Digital Audio Input & OutputsMaking Connections DVD-A or Sacd Player Cable, Satellite, or Hdtv TunerAudio Recorder VCR or Digital Video RecorderFM Antenna Connecting a SubwooferAmplifiers AM AntennaProgramming the RR-1050 Preload Button Using the RR-1050 Audio ButtonFront-panel Display Remote SensorON/OFF Buttons Standby Button Power ButtonVolume Knob Volume Button Surround Mode ButtonsSelecting Inputs Basic OperationsSelecting Digital Inputs Overview Surround FormatsSelecting a Source Input from the Front Panel Selecting a Source from the RemoteDolby Digital Surround EX Dolby DigitalDTS DTS 96/24 DTS Neo62Ch/5Ch/7Ch Stereo Formats Dolby Pro Logic 7.1 Channel SurroundRotel XS 7.1 Channel Surround DSP Music ModesModes Manually Selecting Surround ModesDolby Digital 5.1 discs Dolby Digital Surround EX discs Dolby Digital 2.0 discs DTS 5.1 discs DTS 96/24 discs DTS-ES 6.1 discsMpeg Multichannel discs Analog Stereo Digital Stereo discs PCM, MP3, and HdcdSpeaker Level Other SettingsGroup Delay Contour/Tone SettingsCinema EQ Numeric Buttons Station PresetsNormal Frequency tuning Tuner ControlsRDS and Rbds Tuning Zone 2 Operation To turn Zone 2 on or off To change the Zone 2 volumeControlling Zone 2 from the Main Room Controlling Zone 2 from the Remote LocationMenu Basics Configuring InputsEnglish Buttons to change the selected parameter as follows Multi Input Setup Dolby Pro Logic IICenter Speakers large/small ConfiguringUnderstanding Speaker Configuration Speaker SetupCenter Back Speakers large1 Advance Speaker SetupSpeakers to be configured with custom settings Surround Speakers large/smallSubwoofer Setup Test ToneCrossover 40Hz/60Hz/80Hz/ 100Hz/120Hz/150Hz/200Hz/OFF Speaker front/center/surround/cen Delay SetupContour Setup Calibration with an SPL meterOther Options Zone 2 SetupTo activate memorized User Default Default SetupTo change the Front Redirect setting To memorize User Default settingsTroubleshooting Specifications Rotel of America Rotel EuropeRotel Deutschland