Rotel RSX-1067 owner manual Other Options, Zone 2 Setup

Page 37

Miscellaneous Settings

Other Options

OTHER OPTIONS

RECORD:Source

TURN ON VOL:Last

MAX VOL:Max

VOL SPEED:Slow

POWER:Standby

LANGUAGE:English

VIDEO:NTSC

OSD:On

PROGRESSIVE:NO

MAIN MENU

This OTHER OPTIONS menu, accessed from the MAIN menu, provides access to several miscellaneous settings as follows:

RECORD: Select which source signal to be sent to the recording outputs by choosing one of the input sources. The options are: CD, TAPE, TUNER, VIDEO 1–5, and SOURCE. You can either select a specific component or select SOURCE which will send the signal to the record outputs from whatever source is selected for listening.

TURN ON VOL: Specifies a default volume level to be used each time the RSX-1067 is activated. You can select LAST to have the RSX-1067 power up with the last previously used volume setting. Or, you specify a volume from MIN (full mute) to MAX, in 1dB incre- ments. Note that this setting cannot exceed the MAX VOL established in the next line of the menu.

MAX VOL: Specifies the maximum volume level for the RSX-1067. The volume cannot be adjusted above this level. Settings range from MIN to MAX, in 1dB increments.

VOL SPEED: Provides three options for how rapidly the volume control responds to inputs. The SLOW setting adjusts the volume 1dB with each control input. The MID setting adjusts in 2dB increments. The FAST setting adjusts in 3dB increments.

POWER: This setting determines how the RSX-1067 powers up.

With the default STANDBY setting, the unit powers up in standby mode when AC is ap- plied and the rear panel POWER button is ON. The unit must be activated using the front panel STANDBY button or the remote ON/OFF buttons.

37

With the DIRECT setting, the unit is fully acti- vated when AC power is applied and the rear panel POWER button is ON; however, it may be put in standby mode using the front panel STANDBY button or the remote ON/OFF buttons.

In ALWAYS-ONmode, the unit remains fully active whenever AC is present and the rear panel POWER button is ON; the front panel STANDBY button and the remote ON/OFF buttons are disabled and the unit cannot be put in standby mode.

LANGUAGE: Selects a language for the On Screen Display.

VIDEO: Specifies whether an NTSC or PAL television monitor is connected to the TV MONITOR outputs of the RSX-1067. This set- ting must be correct for the upconversion and OSD menus to work properly.

OSD ON/OFF: Select whether or not status information (such as the volume setting) is displayed on the TV monitor.

PROGRESSIVE: The OSD menus cannot be displayed on the TV monitor when progres- sive scan or 1080i HDTV video signals are being used at the Component Video inputs. This setting enables a feature that allows the display of the main OSD setup menus (but not the information displays such as volume, etc.) on the TV monitor by interrupting the progressive scan video signal and restoring it after the OSD menus are cancelled. Choose the video input or combination of video inputs for progres- sive scan or HDTV video signals (480p, 720p, 1080i). All other video inputs will be assigned as standard interlaced video inputs. Video 4 and 5 cannot be assigned as progressive scan inputs.

NOTE: When a video input or inputs are se- lected for progressive mode, the conversion from composite or S-Video to Component Video output is not available for those inputs. The conversion from composite or S-VIDEO to Component Video output is only available for the other video inputs. For example, if Video 1 and Video 2 are selected for pro- gressive scan signals (V1+V2), conversion from composite or S-Video is only available for Video 3, 4, and 5.

English

Change settings on the OTHER OPTIONS menu by highlighting the desired line using the UP/ DOWN buttons and using the +/– buttons to step through the available settings. To return to the MAIN menu, press the ENTER button. Press the MENU/OSD button on the remote to cancel the display and return to normal operation.

Zone 2 Setup

ZONE2 SETUP

SOURCE:Off

VOLUME SETUP:Variable

VOLUME:60

TURN ON VOL:Last

MAX VOL:Max

12V TRIGGER:Off

MAIN MENU

The ZONE 2 SETUP menu provides settings and configuration options related to the op- eration of Zone 2. This menu is reached by highlighting the ZONE 2 line on the MAIN menu and pressing ENTER.

SOURCE: Specifies a source for listening in Zone 2. Options are CD, TUNER, TAPE, VIDEO 1–5, SOURCE, and OFF. Selecting the SOURCE option links the Zone 2 source to the source selected for the main zone so that Zone 2 will hear the same source as the main zone. Selecting the OFF option turns Zone 2 off.

VOLUME SETUP: configures the Zone 2 outputs for VARIABLE or FIXED volume levels. VARIABLE allows control of the volume settings in Zone 2 from the RSX-1067 front panel or from a remote control/IR repeater in Zone 2. FIXED output disables the Zone 2 volume control. In this mode, the Zone 2 level can be fixed at the level specified on the next line, thus optimizing system performance when send- ing a fixed level signal to a preamp or ampli- fier with its own volume adjustment.

VOLUME: In VARIABLE output mode, this line shows the current volume setting for Zone 2. In FIXED output mode, this volume setting es- tablishes a permanent fixed output level for Zone 2.

Move the highlight to the desired line using the UP/DOWN buttons and use the +/– but- tons to adjust the volume level. To return to the MAIN menu, press the ENTER button. Press the MENU/OSD button on the remote to cancel the display and return to normal operation.

Page 36 Page 38
Image 37
Page 36 Page 38
Contents RSX-1067 Page FCC Information Important Safety InstructionsConsult your authorized Rotel retailer for assistance Controls and Connections RSX-1067Surround Sound ReceiverRR-1050 Remote EnglishHF CONTOUR+5 LF Contour Main Menu On-Screen MenusContents Specifications Other SettingsZone 2 Operation Menu BasicsPlacement Key FeaturesAbout Rotel Getting StartedTape Inputs CD InputsTape Outputs Video 1-5 Audio InputsPreamp Outputs Speaker OutputsZone 2 Audio Outputs Composite Video InputsOther Connections Digital Audio Input & OutputsMaking Connections Audio Recorder Cable, Satellite, or Hdtv TunerVCR or Digital Video Recorder DVD-A or Sacd PlayerAmplifiers Connecting a SubwooferAM Antenna FM AntennaFront-panel Display Using the RR-1050 Audio ButtonRemote Sensor Programming the RR-1050 Preload ButtonVolume Knob Volume Button Standby Button Power ButtonSurround Mode Buttons ON/OFF ButtonsSelecting Inputs Basic OperationsSelecting a Source Input from the Front Panel Overview Surround FormatsSelecting a Source from the Remote Selecting Digital InputsDTS DTS 96/24 Dolby DigitalDTS Neo6 Dolby Digital Surround EXRotel XS 7.1 Channel Surround Dolby Pro Logic 7.1 Channel SurroundDSP Music Modes 2Ch/5Ch/7Ch Stereo FormatsManually Selecting Surround Modes ModesDolby Digital 5.1 discs Dolby Digital Surround EX discs DTS 5.1 discs DTS 96/24 discs DTS-ES 6.1 discs Dolby Digital 2.0 discsMpeg Multichannel discs Analog Stereo Digital Stereo discs PCM, MP3, and HdcdGroup Delay Other SettingsContour/Tone Settings Speaker LevelNormal Frequency tuning Numeric Buttons Station PresetsTuner Controls Cinema EQRDS and Rbds Tuning Zone 2 Operation Controlling Zone 2 from the Main Room To change the Zone 2 volumeControlling Zone 2 from the Remote Location To turn Zone 2 on or offMenu Basics Configuring InputsEnglish Buttons to change the selected parameter as follows Multi Input Setup Dolby Pro Logic IIUnderstanding Speaker Configuration ConfiguringSpeaker Setup Center Speakers large/smallSpeakers to be configured with custom settings Advance Speaker SetupSurround Speakers large/small Center Back Speakers large1Test Tone Subwoofer SetupCrossover 40Hz/60Hz/80Hz/ 100Hz/120Hz/150Hz/200Hz/OFF Contour Setup Delay SetupCalibration with an SPL meter Speaker front/center/surround/cenOther Options Zone 2 SetupTo change the Front Redirect setting Default SetupTo memorize User Default settings To activate memorized User DefaultTroubleshooting Specifications Rotel Europe Rotel of AmericaRotel Deutschland
Top Page Image Contents