PROGRAMMING
Digital Display
7.TO SET THE TIME: Press the “TIME” Button on the Control Panel one time. Use the “UP” & “DOWN” Buttons on the right side of the Control Panel to set the countdown timer hours (23 hour maximum). Press the “TIME” Button again to switch to minutes. Similarly set the minutes (5 minute increments).
8.TO SET THE TEMPERATURE: Press the “TEMP” Button one time. Use the “UP” & “DOWN” Buttons to set the temperature (160oF maximum, 50oF minimum,
5degree increments).
NOTE: Set Temperature is the maximum temperature the Dehydrator could reach during operation.
9.You do not need to push any other buttons. The Dehydrator will automatically start after a brief pause. NOTE: The Dehydrator will start while you’re programming if you delay. Don’t worry, this is normal. Just continue programming as instructed above.
...PROCEED TO “FUNCTION”
FUNCTION
10. The Digital Display on the Control Panel will continuously cycle while the unit |
is operating. It will alternately display: the preset drying time “SET TIME;” the |
remaining drying time “TIME REMAINING;” the preset temperature “SET TEMP;” |
LIGHT BULB REPLACEMENT
WARNING! Before cleaning, assembling or disassembling the Dehydrator, make sure the Dehydrator is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!
1.Turn off the Dehydrator Lights. Turn off and disconnect the Dehydrator from the power outlet.
2.Let the Dehydrator cool. DO NOT attempt to replace a Light Bulb while the Dehydrator is hot.
| LED Light | Wire |
3. Remove all of the Racks. | Fixture | Connector |
|
|
4.Remove the Back Panel of the Dehydrator.
5. Locate the LED Light Fixture that you wish to |
| Wire |
| Connector | |
replace, and disconnect the wires from the Light |
|
|
Fixture from the white Wire Connector on the unit | Push | LED Light |
by squeezing together the two clips on the Wire | MetalClip | Fixture |
Connector. |
|
|
6. Press together the two sides of the Metal Clip on |
|
|
the Light Fixture to release it from the body of the |
| Push |
Dehydrator and then gently push the Light Fixture |
| |
| Metal | |
into the Cabinet of the unit, being sure to have a grip |
| Clip |
on the wires connected to the Light Fixture so it does |
|
|
not drop into the Dehydrator Cabinet. Discard the removed Light Fixture.
7.Insert the replacement Light Fixture into the vacant hole where the old Light Fixture was by first feeding the wire connected to the Light Fixture first.
8.Line up the Light Fixture with the hole and push it back until the Metal Clips on the back of the Light Fixture lock into place.
9.
10.Line the Back Panel of the Dehydrator up and
WHEN DRYING...
and the actual current temperature inside the Dehydrator “ACTUAL TEMP” |
(measured by the Temperature Sensor on the back wall near the top). |
NOTE: The “SET TEMP” is only the highest temperature reached during a heating cycle. The “SET TEMP” is NOT maintained.
11.The Dehydrator will emit 8 beeps at startup and when the interior temperature reaches the preset value.
12.The Dehydrator automatically stops (Fan & Heater) when the countdown timer reaches 0. Unit power will remain on, however.
SAUSAGE OR SNACK
STICKS: Use the Snack
Stick Hangers to hang and dry sausage links and
snack sticks. After removing all the Racks from your Dehydrator, simply drape
the links over the Snack Stick Hangers and slide
them into the top Rack Supports. Be sure not to
allow the links to rest on the bottom of the Cabinet or on top
Rack Supports
of the Diffuser.
...PROCEED TO “POST OPERATION”
GROUND MEATS: Whenever making jerky from ground meats, you can use a jerky gun or such tool to create perfect strips of jerky as well as snack sticks.