Stoelting O111 Extended Storage, Product Consistency Adjustment, Quarterly, Semi-Annually

Page 20

2.Remove the drip tray by gently lifting up to disengage from the support and pulling out. Clean behind the drip tray and front of the freezer with a soap solution.

D.QUARTERLY

WARNING

High voltage will shock, burn or cause death. Turn off and lock out main power disconnect before ser- vicing. Do not operate machine with panels re- moved.

The air-cooled condenser is a copper tube and aluminum fin type. Condensing is totally dependent upon airflow. A plugged condenser filter, condenser, or restrictions in the louvered panel will restrict airflow. This will lower the capacity of the system and damage the compressor.

The condenser must be kept clean of dirt and grease. The freezer must have a minimum of 3” (7.5 cm) of ventilation on the right and left sides of the unit for free flow of air. Make sure the freezer is not pulling over 100° F (37° C) air from other equipment in the area.

The water-cooled condenser is a tube and shell type. The condenser needs a cool, clean supply of water to properly cool the freezer, inlet and discharge lines must be 3/8” I.D. minimum.

The condenser and condenser filter require periodic clean- ing. To clean, refer to the following procedures.

1.Remove the Phillips head screw from the bottom of the right side panel, and then slide the panels down and out.

2.To remove the condenser filter, grasp the top and pull off. Visually inspect for dirt. If the filter is dirty, shake or brush excess dirt off the filter and wash in warm, soapy water. Once the filter is clean rinse thoroughly in warm, clear water and shake dry, taking care not to damage the filter in any way (Figure 28).

3.Visually inspect the condenser for dirt by shining a light through the coil from the back (inside) of the condenser.

4.If the condenser is dirty, place a wet towel over the front (outside) of the condenser.

5.Using a vacuum, carefully clean the condenser coil from the inside and outside of the freezer. A stiff bristled brush may help in releasing debris from between the condenser coils.

E.SEMI-ANNUALLY

1.Check drive belt for proper tension. Push belt in with one finger, belt should deflect about 3/8".

2.Lubricate condenser fan motor with S.A.E. 20 weight oil. Three to six drops is required.

CAUTION

Do not over-lubricate; resulting damage could cause motor failure.

3.14 EXTENDED STORAGE

Refer to the following steps for storage of the freezer over any long period of shutdown time:

A.Turn the Main Freezer Power OFF-ON switch to the OFF position.

B.Disconnect (unplug) from the electrical supply source.

C.Clean thoroughly with a warm water detergent all parts that come in contact with the mix. Rinse in clean water and dry parts. Do not sanitize.

NOTE

Do not let the cleaning solution stand in the hopper or in the freezer barrel during the shutdown period.

D.Remove, disassemble and clean the front door, mix inlet regulator and auger parts. Place the auger flights and the front auger support bushing in a plastic bag with a moist paper towel to prevent them from becoming brittle.

E.In a water cooled freezer, disconnect water lines and drain water. With a flathead screwdriver, hold the water valve open and use compressed air to clear the lines of any remaining water.

3.15 PRODUCT CONSISTENCY ADJUSTMENT

The IntelliTec control monitors the consistency (firmness) of the product (mix) in the freezing cylinder by monitoring the drive motor amp draw. When consistency is reached, the drive motor and refrigeration system will shut off. The control panel on the front of the freezer allows the operator to adjust the freezing cylinder to create the desired product consistency.

A.Place the FREEZING CYLINDER OFF/ON switch in the ON position.

B.Press the SET button on the Control Panel once. Fine Adj will appear on the LCD screen (Fig. 3- 12).

14

Page 19 Page 21
Image 20
Page 19 Page 21
Contents O111 IntelliTec Models Page STOELTING, LLC Few Words About Safety Table of Contents List of Illustrations Section Description and Specifications DescriptionModel Optima Countermodel Gravity Freezer Dimensions WeightElectrical CoolingSection Installation Instructions Safety PrecautionsSTOELTING, INC 502 Hwy Kiel, Wisconsin3FREEZERINSTALLATION Shipment and Transit208/230V 115V 20 AmpOperating Controls and Indicators Section Initial Setup and OperationOPERATOR’S Safety Precautions Menu Navigation Buttons Dispense Rate AdjustersFront Door Safety Switch When sanitizing the freezer, refer to local sanitary regula SanitizingFreeze Down and Operation Sanitizing HopperCleaning the Freezer Disassembly of Freezer PartsMIX Information Removing MIX from FreezerCleaning the Freezer Parts Wear LineAssembly of Freezer Sanitize Freezer and Freezer PartsRoutine Cleaning Preventive MaintenanceCleaning and Sanitizing Information Important Differences Between Cleaning and SanitizingWeekly Additional InformationDaily Product Consistency Adjustment Extended StorageQuarterly SEMI-ANNUALLYLocking OUT Control Panel 13 Product Consistency ControlPage Section Troubleshooting Error CodesTroubleshooting Error Code MalfunctionAlternating Flashing Control Panel Lights Problem Possible Cause Remedy Temperature Below 40F 4C Drive beltSlipping or SquealingSection Replacement Parts HOW to Order PartsBRUSHES, DECALS, and Lubrication Part DescriptionO111 Replacement Parts Part Description Quantity Page Warranty Soft Serve / Shake Freezers AS is

O111 specifications

The Stoelting O111 is an advanced soft serve ice cream machine, designed for both high-volume production and unparalleled quality. This machine showcases a blend of efficiency, reliability, and user-friendly features, making it an ideal choice for ice cream parlors, restaurants, and catering services.

One of the main features of the Stoelting O111 is its high-capacity output, capable of producing a significant volume of soft serve in a short period. The machine is designed to handle busy environments, ensuring that customers receive their desserts quickly, which is essential during peak hours. It typically offers dual-flavor capabilities, allowing the simultaneous dispensing of two different ice cream flavors. This not only enhances customer choice but also provides the opportunity for creative mix-ins and swirls.

In terms of technology, the Stoelting O111 is equipped with a state-of-the-art refrigeration system that maintains optimal product consistency. This system includes a direct drive compressor, which ensures efficient cooling while minimizing energy consumption. The machine also features a temperature control panel that allows operators to adjust the serving temperature for different products, thereby enhancing the overall quality and texture of the soft serve.

Another standout characteristic of the Stoelting O111 is its intuitive digital controls. These controls provide operators with real-time monitoring of the machine’s performance, enabling them to make quick adjustments as necessary. The easy-to-read display shows information on the mix levels, temperature settings, and machine status, allowing for proactive maintenance and minimal downtime.

Moreover, the Stoelting O111 prioritizes hygiene and ease of cleaning. It features a removable mix hopper and dispensing nozzle, facilitating thorough cleaning procedures. This focus on maintenance aligns with health standards, ensuring that the soft serve produced remains safe and high-quality.

With its robust construction, user-friendly interface, and advanced technologies, the Stoelting O111 stands out as a reliable machine that caters to the demands of the modern food service industry. Whether it's for a busy ice cream shop or a special event, the Stoelting O111 delivers exceptional performance and superior soft serve, making it a valuable addition to any establishment.
Top Page Image Contents