Stoelting O111 owner manual Section Troubleshooting, Error Codes, Error Code Malfunction

Page 23

SECTION 4

TROUBLESHOOTING

4.1 ERROR CODES

When the freezer experiences a problem, one of the following error codes will be displayed on the control panel. Each error code directs you to the system location of the malfunction.

ERROR CODE MALFUNCTION

1Soft

2High Torque

3Extended Run Time

4Clean

5Barrel Sensor

6Hopper Sensor

7Drive Motor

8Cab Sensor

9High Pressure Cutout

10 Auxiliary Sensor

11 Low Temperature

To return the freezer to normal operation, any error caus- ing condition must be corrected and the Freezing Cylinder Off-On switch must be placed in the Off position and back in the On position before the affected side of the freezer will return to normal operation.

4.2TROUBLESHOOTING

Error Code 1 - Soft Error

The Soft Error (E1) is an internal control board error that is logged for future analysis. The refrigeration is never stopped and the freezer will continue to operate normally.

Error Code 2 - High Torque

If the control panel displays a High Torque Error (E2), the controller has sensed that the drive motor is running at 125% of the preset CutOut amp setting for 10 or more seconds. This may be due to the product consistency adjustment being set too high. Place the Main Power OFF-ON switch in the OFF position, wait until the product in the barrel thaws to a reasonably soft consistency and return the switch to the ON position. Follow the instructions in Section 3 to reduce the product consistency by a few levels. If the error persists, contact your Authorized Stoelting Distributor for further assistance.

Error Code 3 - Run Time

The Run Time Error (E3) occurs when the compressor runs continuously for 30 minutes without the product reaching consistency in “Serve Mode” or if the product does not reach proper temperature in “Sleep 2 Mode”. This error is generally caused by very low mix levels in the freezer’s mix container or from product breakdown. Another common cause results from a restriction preventing mix from entering the freezing cylinder. Check the mix in the hopper. If the level mix is low, add mix. If there is a possibility that the mix is broken down, clean and sanitize the freezer and replace the mix with fresh product.

Ice crystals in the hopper can clog the mix inlet system and prevent mix from entering the freezing cylinder. Thoroughly thaw mix per manufacturer’s recommendations. To check for ice crystals, pour a small amount of product in the hopper through a clean and sanitized sieve or strainer. If ice crystals are in the mix, check the temperature of the walk-in cooler where the mix is stored or the temperature of the freezer’s cabinet.

The Run Time Error may also occur if airflow within the freezer has reduced or stopped. Check the sides and top of the freezer for anything that would restrict airflow.

If the error persists after attempting to clear it, contact your Authorized Stoelting Distributor for further assistance.

Error Code 4 - Clean

If the freezer is left in the Clean Mode for more than 20 minutes, the control panel will display a Clean Error (Error 04). This condition does not reflect a problem with the freezer itself. The Clean Error has been programmed into the controller as a safeguard to protect the freezer from potential damage caused by the freezer being accidentally left in “Clean Mode”. The control will attempt to restart itself after 5 minutes. The display will then flash and read Restart. To immediately clear the Clean Error, place the Main Power Off-On switch in the Off position and back in the On position. After the Clean Error has been cleared, the freezer will start a refrigeration cycle to protect the product in case the clean button was pressed by mistake.

17

Image 23
Contents O111 IntelliTec Models Page STOELTING, LLC Few Words About Safety Table of Contents List of Illustrations Description Section Description and SpecificationsCooling Model Optima Countermodel Gravity Freezer DimensionsWeight Electrical502 Hwy Kiel, Wisconsin Section Installation InstructionsSafety Precautions STOELTING, INC115V 20 Amp 3FREEZERINSTALLATIONShipment and Transit 208/230VOperating Controls and Indicators Section Initial Setup and OperationOPERATOR’S Safety Precautions Menu Navigation Buttons Dispense Rate AdjustersFront Door Safety Switch Sanitizing When sanitizing the freezer, refer to local sanitary regulaSanitizing Hopper Freeze Down and OperationRemoving MIX from Freezer Cleaning the FreezerDisassembly of Freezer Parts MIX InformationWear Line Cleaning the Freezer PartsSanitize Freezer and Freezer Parts Assembly of FreezerImportant Differences Between Cleaning and Sanitizing Routine CleaningPreventive Maintenance Cleaning and Sanitizing InformationWeekly Additional InformationDaily SEMI-ANNUALLY Product Consistency AdjustmentExtended Storage Quarterly13 Product Consistency Control Locking OUT Control PanelPage Error Code Malfunction Section TroubleshootingError Codes TroubleshootingAlternating Flashing Control Panel Lights Problem Possible Cause Remedy Squealing Temperature Below 40F 4CDrive belt Slipping orPart Description Section Replacement PartsHOW to Order Parts BRUSHES, DECALS, and LubricationO111 Replacement Parts Part Description Quantity Page AS is Warranty Soft Serve / Shake Freezers

O111 specifications

The Stoelting O111 is an advanced soft serve ice cream machine, designed for both high-volume production and unparalleled quality. This machine showcases a blend of efficiency, reliability, and user-friendly features, making it an ideal choice for ice cream parlors, restaurants, and catering services.

One of the main features of the Stoelting O111 is its high-capacity output, capable of producing a significant volume of soft serve in a short period. The machine is designed to handle busy environments, ensuring that customers receive their desserts quickly, which is essential during peak hours. It typically offers dual-flavor capabilities, allowing the simultaneous dispensing of two different ice cream flavors. This not only enhances customer choice but also provides the opportunity for creative mix-ins and swirls.

In terms of technology, the Stoelting O111 is equipped with a state-of-the-art refrigeration system that maintains optimal product consistency. This system includes a direct drive compressor, which ensures efficient cooling while minimizing energy consumption. The machine also features a temperature control panel that allows operators to adjust the serving temperature for different products, thereby enhancing the overall quality and texture of the soft serve.

Another standout characteristic of the Stoelting O111 is its intuitive digital controls. These controls provide operators with real-time monitoring of the machine’s performance, enabling them to make quick adjustments as necessary. The easy-to-read display shows information on the mix levels, temperature settings, and machine status, allowing for proactive maintenance and minimal downtime.

Moreover, the Stoelting O111 prioritizes hygiene and ease of cleaning. It features a removable mix hopper and dispensing nozzle, facilitating thorough cleaning procedures. This focus on maintenance aligns with health standards, ensuring that the soft serve produced remains safe and high-quality.

With its robust construction, user-friendly interface, and advanced technologies, the Stoelting O111 stands out as a reliable machine that caters to the demands of the modern food service industry. Whether it's for a busy ice cream shop or a special event, the Stoelting O111 delivers exceptional performance and superior soft serve, making it a valuable addition to any establishment.