Setting Warmer Drawer Controls contd | Kenmore 790.9634 specification

Setting Warmer Drawer Controls (cont'd)

To Remove Warmer Drawer:

1. _	Turn powerOFF before removing thewarmerdrawer.

2.Open the drawer to the fully opened position.

3.On the right glide you will find a shield attached with a hex-head screw (see figure 1). Using a 1!4" socket and ratchet remove the shield.

4.Locate glide lever on each side of drawer, pull up on the left glide lever and push down on the right glide lever.

5.Pull the drawer away from the range.

To Replace Warmer Drawer:

1.Replace shield on the right glide of the drawer body.

2.Pull the bearing glides to the front of the chassis glide (see

figure 2).

3.Align the glide on each side of the drawer with the glide slots on the range.

4.Push the drawer into the range until levers "click" (approximately 2"). Pull the drawer open again to seat bearing glides into position. if you do not hear the levers "click" or the bearing glides do not feel seated remove the drawer and repeat steps 2-4. This will minimize possible damage to the bearing glides.

Remove	shield	on	righ
glide	Pull up	on	left	lever
while	pushing	down		on

P.,.d ....... hflnger ............................................................

Fig 1

Fig. 2

Self-Cleaning

During the Self-Cleaning cycle, the outside of the range can become very hot to the touch. DO NOT leave small children unattended near the appliance.

The health of some birds is extremely sensitive to the fumes given off during the Self-Cleaning cycle of any range. Move birds to another well-ventilated room.

DO NOT line the oven walls, racks, OVEN BOTTOM or any part of the range with aluminum foil. Doing so will destroy heat distribution, produce poor baking results & cause permanent damage to the oven interior (aluminum foil will melt to the interior surface of the oven).

DO NOT force the oven door open. This can damage the automatic door locking system. Use caution when opening the door after the Self-Cleaning cycle is completed. The oven may still be VERY HOT.

Self-Cleaning Oven

A Self-Cleaning oven cleans itself with high temperatures (well above cooking temperatures) which eliminate soils completely or reduces them to a fine powdered ash you can wipe away with a damp cloth.

Prepare for the Self-Cleaning Cycle with the following

precautions:

*DO NOT use oven cleaners or oven protective coatings in or around any part of the Self-Cleaning oven.

*DO NOT clean the oven door gasket. The woven

material of the oven door gasket is essential for a good seal. Care should be taken not to rub, damage or remove the gasket.

*DO NOT use any cleaning materials on the oven door gasket. Doing so could cause damage.

*Remove the broiler pan & insert, all utensils & ANY aluminum foil. These items cannot withstand high cleaning temperatures.

*Remove the oven racks. If the racks are left in the oven during the Self-Clean cycle their color will turn slightly blue & the finish will be dull. After the cycle is complete and the oven has cooled, rub the sides of the oven racks with wax paper or a cloth containing a small amount of salad oil (this will make the oven racks glide easier into the oven rack positions).

*Remove any excessive spillovers in the oven cavity before starting the Self-Cleaning cycle. To clean, use hot, soapy water and a cloth. Large spillovers can cause heavy smoke or fire when subjected to high temperatures. DO NOT allow food spills with a high sugar or acid content (such as milk, tomatoes, sauerkraut, fruit juices or pie filling) to remain on the surface as they may leave a dull spot even after cleaning.

*Clean any soil from the oven frame, the door liner outside the oven door gasket and the small area at the front center of the oven bottom. These areas heat sufficiently to burn soil on. Clean with soap and water.

*NOTE: Prior to setting the Self-Clean cycle, any spills remaining on the oven bottom should be removed.