Kenmore 795.7977 manual Before YOU Begin, What YOU will Need, Shut OFF the Main Water Supply

Page 32

BEFORE YOU BEGIN

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double-insulated or grounded in a manner to prevent the hazard of electric shock, or is battery-powered.

All installations must be in accordance with local plumbing code requirements.

NOTE: Wear eye protection.

WHAT YOU WILL NEED

•Copper Tubing, 1/4" outer diameter to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 8 feet (2.4 m). Be sure there is sufficient extra tubing (about 8 feet [2.4 m] coiled into 3 turns of about 10" [25 cm]

diameter) to allow the refrigerator to move out from the wall after installation.

•A cold water supply. The water pressure must be between 20 and 120 p.s.i, on models without a water filter and between 40 and 120 p.s.i, on models with a water filter.

•Power drill.

•1/2" or adjustable wrench.

•Straight- and Phillips- blade screwdriver.

•Two 1/4" outer diameter compression nuts and 2 ferrules (sleeves) to connect the copper tubing to the shutoff valve and the refrigerator water valve.

•If your existing copper water line has a flared fitting at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to the

refrigerator OR you can

cut off the flared fitting with a tube cutter and then use a compression fitting.

•Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32" at

the point of connection to the

COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

NOTE: Self Piercing Saddle Type Water Valve should not be used.

INSTALLATION INSTRUCTIONS

Install the shutoff valve on the nearest frequently used drinking water line.

1.SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet to relieve the pressure on the line.

2.CHOOSE THE VALVE LOCATION

Choose a location for the valve that

is easily accessible. It is best to connect into the side of a vertical

water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to

avoid drawing off any sediment from the water pipe.

3.DRILL THE HOLE FOR THE VALVE

Drill a 1/4" hole in the water pipe using a sharp bit. Remove any burrs resulting from drilling

the hole in the pipe. Take care not to allow water to drain into

the drill. Failure to drill a 1/4" hole may result in reduced ice production or smaller cubes.

NOTE: The hookup line cannot be white, plastic tubing. Licensed plumbers must use only copper tubing NDA tubing #49595 or 49599 or Cross Link Polyethylene(PEX) tubing.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Mmtrio Line 32-34 Troubleshooting Guide 35-38 Kenmore Elite Limited Warranty Disclaimer of implied warranties limitation of remediesMaster Protection Agreements Basic Safety Precautions To Connect Electricity Recommended Grounding MethodBefore YOU Throw Away Your OLD Refrigerator Or Freezer USE of Extension CordsFixed Door Bin Extra Ice Bin p Unpacking Your Refrigerator InstallationWhen Moving Your Refrigerator Removing Freezer Drawer Handle HOW to Remove Door HandlesRemoving Refrigerator Handle Replacing Freezer Drawer Handle HOW to Replace Door HandlesReplacing Refrigerator Door Handle To remove the right refrigerator door Removing and Replacing Refrigerator DoorsTo remove the left refrigerator door Reinstalling the Refrigerator Door Right Door Left DoorHOW to Remove and Reinstall Pullout Drawer Removing Pullout Drawer Top DrawerRemoving Pullout Drawer Bottom drawer Reinstalling Pullout Drawer Top Drawer Risk of Child EntrapmentReinstalling Pullout Drawer Bottom drawer To remove the base cover Leveling and Door AlignmentLeveling Dispenser UltralceFilter Light / Light SensorAlarm Temperature Mode Switch FunctionF -CPower Saving Mode LockIN-DOOR ICE Bank Adjusting Control Settings Food Storage GuideStoring Frozen Food Water DispenserPackaging Packaging recommendationsRefrigerator Shelves Temperature Controlled Pantry Drawer Humidity Controlled CrisperRemoving Humidity Controlled Crisper Modular Door BINDurabase Divider Extra ICE BIN DurabaseAirflow Do not block any of the cool air vents with foodReplace with a new cartridge FilterRemove the old cartridge To reduce risk of property damage due to water leakage General Cleaning Tips Light Bulb ReplacementOutside Door Liners and Gaskets When YOU Move Power Interruptions When YOU GO on Vacation Automatic Icemaker Personal Injury HazardPreparing for Vacation When YOU should SET the IcemakerNormal Sounds YOU MAY Hear Before YOU Begin What YOU will NeedShut OFF the Main Water Supply Choose the Valve LocationFasten the Shutoff Valve Tighten the Pipe ClampConnect the Tubing to the Valve Flush OUT the TubingConnect the Tubing to the Refrigerator Turn the Water on AT the Shutoff ValvePlug in the Refrigerator Start the IcemakerUnderstanding Sounds YOU MAY Hear Refrigerator does not OperateLights do not Work Check ifVibration or Rattling Noise Compressor Motor Seems to RUN TOO MuchDoors will not Close Completely Check if ThenFrost or ICE Crystals on Frozen Food ICE has OFF-TASTE or OdorThere is Water in the Defrost Drain PAN Refrigerator Seems to Make TOO Much NoiseCubes Produced by Icemaker are TOO Small Doors are Difficult to OpenIs Interior Moisture Buildup CheckifPage Anage
Top Page Image Contents