Do S C and a ignment, Supply Con eot s

D®o' _ S _ C and A ignment' "_

Door Closing

1.Move the refrigerator into its final position.

2.Place a level inside the refrigerator at the back of the top shelf (see Graphic 8).

3.Locate the leveling screws behind the base grille of the refrigerator on either side.

4.Use a hex-head socket wrench to adjust the rear roller leveling screws until the refrigerator is level. Turn the rear roller leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side (see Graphic 9). Make sure refrigerator is level before proceeding.

5.Check the door alignment after leveling the refrigerator.

Locate a _/2in. to 1V4in. (1.25 cm to 3.18 cm) vertical COLD water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use V4in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a V4in. hole in the cold water pipe you have selected.

Door Alignment

If the doors are uneven after leveling the product (see Graphic 10), follow the steps below.

1.Use a hex-head socket wrench to adjust the front roller leveling screws until the doors are even. Turn the front roller leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side (see Graphic 11).

NOTE: Open and close both the refrigerator and freezer doors after each adjustment to check the door alignment.

2.Open the doors and replace the base grille. Line up the grille support tabs with the metal clips. Push the grille firmly to snap it into place.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Supply Con eot © s

Read all directions carefully before you begin.

IMPORTANT:

•If you turn the refrigerator on before the water line is connected, turn the ice maker OFR

•All installations must meet local plumbing code requirements.

•Use copper tubing and check for leaks. Install copper tubing only in areas where temperatures will remain above freezing.

Tools required: Standard screwdriver, 7/16in. and V2in. open-end wrenches or two adjustable wrenches, V4in. nut driver and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a V4in. (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/1ein. (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Cold water supply

Connect the ice maker to a cold water line with water pressure between 30 and 120 psi. If you have questions about your water pressure, call your utility company.

Connecting to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

1. Cold Water Pipe	5. Compression Sleeve
2. Pipe Clamp	6. Shutoff Valve
3. Copper Tubing	7. Packing Nut

4.Compression Nut

6.Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the V4in. drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connecting to Refrigerator

1.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown.

This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.

2, Turn shutoff valve ON.

3.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

--1

1.	Tube Clamp	3.	Compression Nut
2.	Copper Tubing	4.	Valve Inlet

4.The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the V4in. (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

5.Plug in refrigerator or reconnect power.