Murray 425620x92B manual HOW to USE the Speed Control Pedal, HOW to Disconnect the Transmission

Page 16

OPERATION

HOW TO USE THE SPEED CONTROL PEDAL

The drive system uses a Hydrostatic Automatic Drive transmission. The Hydrostatic transmission is very easy to operate. This type of drive system does not require a shift lever or a clutch pedal.

The speed and direction of travel is controlled by a single speed control pedal operated with your right foot. Do not use the left brake pedal in normal operation. Only use the left brake pedal to quickly stop in an emergency.

HOW TO DRIVE FORWARD

1.The automatic drive disconnect must be in the DRIVE position (Figure 8).

2.Slowly release your left foot from the brake pedal.

3.Move the throttle control to the FAST position.

4.Slowly push the speed control pedal forward to the desired speed (Figure 7).

5.To increase forward speed, slowly move the speed control pedal forward. To reduce forward speed, slowly release the speed control pedal until the unit slows to the desired speed.

Speed Control

Pedal

Figure 7

HOW TO DRIVE IN REVERSE

1.Look to the rear.

2.Slowly push the speed control pedal to the REVERSE position.

HOW TO CHANGE DIRECTIONS

CAUTION: To change directions, do not use the left brake pedal. Use only the speed control pedal.

1.Slowly remove your foot from the speed control pedal. The speed control pedal will automatically return to the NEUTRAL position.

2.When the unit stops, slowly move the speed control pedal to the desired direction.

SPEED CONTROL PEDAL POSITIONS

The forward speed is controlled by the position of the speed control pedal. The following chart provides functions along with the pedal positions. Always operate the engine with the throttle control in the FAST position.

FUNCTION

PEDAL

THROTTLE

 

POSITION

 

 

 

 

Trimming

1/3

 

Snow Thrower

 

 

 

 

 

Bagging Grass

1/3 to 1/2

 

 

 

FAST

 

 

CHOKE

Normal Mowing

1/2 to 2/3

FAST

 

 

 

 

SLOW

Easy Mowing

1/2 to 3/4

THROTTLE

Snow Blade

 

 

 

 

Transport

FULL

 

 

 

 

Pull Behind

1/3 to 1/2

 

Attachments

 

 

 

 

 

HOW TO DISCONNECT THE TRANSMISSION

To push the unit, use the automatic drive disconnect to release the transmission. The automatic drive disconnect is under the seat.

1.The engine must be off.

2.Raise the seat. The automatic drive disconnect is under the seat.

3.Move and latch the automatic drive disconnect in the PUSH position (Figure 8). The transmission is now released and the unit can be pushed.

NOTE: In cold weather, the heavy viscosity oil in the transmission will make the unit difficult to push.

4.To engage the transmission, unlatch the automatic drive dis- connect. The transmission is now connected and ready to op- erate.

F-040740L

16

Automatic Drive Disconnect

PUSH POSITION

Seat

Automatic Drive Disconnect

DRIVE POSITION

Figure 8

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Table of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables HOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionHOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineCarburetor Operating Tips Mowing and Bagging TipsMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Where to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart 040740L USARepair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Electrical System Light HarnessElectrical System 040740L Index Model No Model No Bushel Capacity

425620x92B specifications

Murray 425620x92B is a notable power tool that has gained attention for its user-friendly design and efficient performance. This model is primarily designed for carpentry and woodworking enthusiasts, making it an excellent choice for both professionals and hobbyists.

One of the main features of the Murray 425620x92B is its robust motor. With a power rating that allows it to handle demanding tasks, this tool provides reliable performance whether you’re cutting, shaping, or smoothing wood. The motor is engineered for longevity, ensuring that users can depend on it for various projects without frequent breakdowns.

The design of the Murray 425620x92B enhances its usability. It includes an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. This is particularly important for users who engage in long hours of work, as comfort can significantly impact efficiency and precision.

In terms of technology, the Murray 425620x92B incorporates advanced safety features. It is equipped with an automatic shut-off function, which activates when the tool overheats. This precautionary measure ensures that users can operate the tool safely, minimizing the risk of accidents. Furthermore, its safety switch prevents accidental start-ups, providing an extra layer of security.

The precision of the Murray 425620x92B is another standout characteristic. With adjustable settings, users can easily modify the depth and speed of cuts according to their needs. This versatility allows for a wide range of applications, from delicate trimming to more aggressive cutting tasks. Additionally, the tool features a dust collection system that helps maintain a clean work environment, reducing cleanup time and enhancing visibility during operation.

Durability is also a hallmark of the Murray 425620x92B. Constructed with high-quality materials, this tool can withstand the rigors of continuous use in various work conditions. Its design includes protective casing that shields internal components from dust and debris, further extending its lifespan.

In conclusion, the Murray 425620x92B is a powerful, versatile, and safe tool ideal for woodworking tasks. Its combination of performance, comfort, safety features, and durability makes it a top choice for those looking to invest in a reliable power tool. Whether you’re a seasoned professional or just starting in the woodworking world, the Murray 425620x92B promises to meet and exceed your expectations.
Top Page Image Contents