Murray 425620x92B manual Trouble Shooting Chart

Page 34

TROUBLE SHOOTING CHART

PROBLEM: The engine will not start.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric-Start Models: Clean the battery terminals. Tighten the cables.

3.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

4.Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position. Try to start the en- gine several times. Install the spark plug.

5.Replace the spark plug.

6.Adjust the carburetor.

PROBLEM: The engine will not turn over.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric-Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery.

3.Replace the fuse.

4.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

5.Electric-Start Models: replace the solenoid. Recoil-Start Mod-

els: replace the module.

PROBLEM: The engine is difficult to start.

1.Adjust the carburetor.

2.Replace the spark plug.

3.Replace the fuel filter.

PROBLEM: The engine does not run smooth or has a loss of power.

1.Check the oil.

2.Clean the air filter.

3.Clean the air screen.

4.Replace the spark plug.

5.The engine is working too hard. Use a lower gear.

6.Adjust the carburetor.

7.Replace the fuel filter.

PROBLEM: The engine does not run smooth at fast speed.

1.Replace the spark plug.

2.Adjust the throttle control.

3.Clean the air filter.

4.Replace the fuel filter.

PROBLEM: The engine stops when the blades are engaged.

1.To activate the seat sensor, always sit in the middle of the seat.

2.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

PROBLEM: On slopes, the engine stops.

1.Mow up and down slopes. Never mow across a slope.

2.To activate the seat sensor, always sit in the middle of the seat.

PROBLEM: The engine will not idle.

1.Replace the spark plug.

2.Clean the air filter.

3.Adjust the carburetor.

4.Adjust the throttle control.

5.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

PROBLEM: A hot engine causes a decrease in power.

1.Clean the air screen.

2.Check the oil.

3.Adjust the carburetor.

4.Replace the fuel filter.

PROBLEM: Excessive vibration.

1.Replace the blade.

2.Check for loose engine bolts.

3.Decrease the air pressure in the tires.

4.Adjust the carburetor.

5.Check for a damaged belt or damaged pulley. Replace the damaged parts.

PROBLEM: The grass does not discharge correctly.

1.Stop the engine. Clean the mower housing.

2.Raise the height of cut.

3.Replace or sharpen the blade(s).

4.Move the shift lever to a slower speed.

5.Move the throttle control to the FAST position.

6.Replace the spring for the blade idler.

PROBLEM: The mower housing does not cut level.

1.Check the air pressure in the tires.

2.Adjust the level of the mower housing.

3.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The mower blades will not rotate.

1.Check the mower drive belt. Make sure the belt is installed cor- rectly.

2.Replace the mower drive belt.

PROBLEM: The unit will not move when the brake is released and the speed control pedal is depressed.

1.Check the motion drive belt. Make sure the belt is installed correctly.

2.Adjust the clutch.

3.Replace the motion drive belt.

4.Release the Automatic Drive Disconnect under the seat.

PROBLEM: The unit moves slower or stops when the speed control pedal is depressed.

1.Adjust the clutch.

2.Replace the motion drive belt.

PROBLEM: When the brake pedal is released, belt noise can be heard.

1.Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides.

2.If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over uneven terrain.

1.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

F-040740L

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model Table of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionHOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceFrequency Maintenance Required Comments General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Where to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart 040740L USARepair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Electrical System Light HarnessElectrical System 040740L Index Model No Model No Bushel Capacity

425620x92B specifications

Murray 425620x92B is a notable power tool that has gained attention for its user-friendly design and efficient performance. This model is primarily designed for carpentry and woodworking enthusiasts, making it an excellent choice for both professionals and hobbyists.

One of the main features of the Murray 425620x92B is its robust motor. With a power rating that allows it to handle demanding tasks, this tool provides reliable performance whether you’re cutting, shaping, or smoothing wood. The motor is engineered for longevity, ensuring that users can depend on it for various projects without frequent breakdowns.

The design of the Murray 425620x92B enhances its usability. It includes an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. This is particularly important for users who engage in long hours of work, as comfort can significantly impact efficiency and precision.

In terms of technology, the Murray 425620x92B incorporates advanced safety features. It is equipped with an automatic shut-off function, which activates when the tool overheats. This precautionary measure ensures that users can operate the tool safely, minimizing the risk of accidents. Furthermore, its safety switch prevents accidental start-ups, providing an extra layer of security.

The precision of the Murray 425620x92B is another standout characteristic. With adjustable settings, users can easily modify the depth and speed of cuts according to their needs. This versatility allows for a wide range of applications, from delicate trimming to more aggressive cutting tasks. Additionally, the tool features a dust collection system that helps maintain a clean work environment, reducing cleanup time and enhancing visibility during operation.

Durability is also a hallmark of the Murray 425620x92B. Constructed with high-quality materials, this tool can withstand the rigors of continuous use in various work conditions. Its design includes protective casing that shields internal components from dust and debris, further extending its lifespan.

In conclusion, the Murray 425620x92B is a powerful, versatile, and safe tool ideal for woodworking tasks. Its combination of performance, comfort, safety features, and durability makes it a top choice for those looking to invest in a reliable power tool. Whether you’re a seasoned professional or just starting in the woodworking world, the Murray 425620x92B promises to meet and exceed your expectations.
Top Page Image Contents