Murray 425620x92B manual HOW to Check and Adjust the Drive Brake

Page 25

MAINTENANCE

HOW TO CHECK AND ADJUST THE DRIVE BRAKE

Completely push the brake pedal forward. Set the parking brake. Move the automatic drive disconnect to the PUSH position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows.

1.The location of the drive brake is on the right side of the gearbox (Figure 20).

2.Make sure the parking brake is set and the automatic drive disconnect is in the PUSH position. Turn the hex nut in a clockwise direction until the rear wheels do not turn when the unit is pushed forward.

3.Release the parking brake and push the unit. If the unit does not roll, turn the hex nut in a counterclockwise direction until the unit rolls.

4.Set the parking brake. Push the unit. If the rear wheels do not turn, the drive brake is correctly adjusted. Release the parking brake.

WARNING: If you cannot correctly adjust the drive brake, replace the brake pads. Correct replacement parts and assistance are available from an autho- rized service center.

Drive Brake

 

Hex Nut

Gearbox

 

 

Figure 20

MAINTENANCE FREE BATTERY

HOW TO REMOVE THE BATTERY

To charge or clean the battery, remove the battery from the unit as follows.

WARNING: To prevent sparks, disconnect the black battery cable from the negative (-) terminal before you disconnect the red cable.

WARNING: The battery contains sulfuric acid which is harmful to the skin, eyes and clothing. If the acid gets on the body or clothing, wash with water.

1.Disconnect the black cable from the negative (-) terminal (Figure 21).

2.Disconnect the red cable from the positive (+) terminal.

3.Lift the battery tray and the battery out of the unit.

HOW TO CLEAN THE BATTERY

1.Remove the battery.

2.Wash the battery with a solution of one gallon of water and four tablespoons of baking soda (sodium bicarbonate). Make sure the solution does not get into the battery cells.

3.Clean the terminals and the ends of the cables with a wire brush.

4.Install the battery.

5.To prevent corrosion, apply grease to the battery terminals.

HOW TO CHARGE THE BATTERY

WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion.

1.Before you charge the battery, remove the battery.

2.To charge the battery, use a 12 volt battery charger. Charge at a rate of 6 amperes for 1 hour.

3.Install the battery.

WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable.

4.Fasten the red cable to the positive (+) terminal with the fas- teners as shown.

5.Fasten the black cable to the negative (-) terminal with the fas- teners as shown.

 

Positive (+)

 

 

Terminal

 

Wing Nut

 

Red Cable

 

 

Carriage Bolt

 

 

Battery

Black Cable

 

Battery Tray

 

 

 

Carriage Bolt

Figure 21

 

 

F-040740L

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables Check the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresLocation of Controls OperationAttachments HOW to USE the Throttle ControlHOW to Disconnect the Transmission HOW to USE the Speed Control PedalHOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingBefore Starting the Engine HOW to Start the EngineCarburetor Mowing and Bagging Tips Operating TipsFrequency Maintenance Required Comments MaintenanceHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltHOW to Check and Adjust the Drive Brake HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Removal HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart USA 040740LChassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Light Harness Electrical SystemElectrical System 040740L Index Model No Bushel Capacity Model No

425620x92B specifications

Murray 425620x92B is a notable power tool that has gained attention for its user-friendly design and efficient performance. This model is primarily designed for carpentry and woodworking enthusiasts, making it an excellent choice for both professionals and hobbyists.

One of the main features of the Murray 425620x92B is its robust motor. With a power rating that allows it to handle demanding tasks, this tool provides reliable performance whether you’re cutting, shaping, or smoothing wood. The motor is engineered for longevity, ensuring that users can depend on it for various projects without frequent breakdowns.

The design of the Murray 425620x92B enhances its usability. It includes an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. This is particularly important for users who engage in long hours of work, as comfort can significantly impact efficiency and precision.

In terms of technology, the Murray 425620x92B incorporates advanced safety features. It is equipped with an automatic shut-off function, which activates when the tool overheats. This precautionary measure ensures that users can operate the tool safely, minimizing the risk of accidents. Furthermore, its safety switch prevents accidental start-ups, providing an extra layer of security.

The precision of the Murray 425620x92B is another standout characteristic. With adjustable settings, users can easily modify the depth and speed of cuts according to their needs. This versatility allows for a wide range of applications, from delicate trimming to more aggressive cutting tasks. Additionally, the tool features a dust collection system that helps maintain a clean work environment, reducing cleanup time and enhancing visibility during operation.

Durability is also a hallmark of the Murray 425620x92B. Constructed with high-quality materials, this tool can withstand the rigors of continuous use in various work conditions. Its design includes protective casing that shields internal components from dust and debris, further extending its lifespan.

In conclusion, the Murray 425620x92B is a powerful, versatile, and safe tool ideal for woodworking tasks. Its combination of performance, comfort, safety features, and durability makes it a top choice for those looking to invest in a reliable power tool. Whether you’re a seasoned professional or just starting in the woodworking world, the Murray 425620x92B promises to meet and exceed your expectations.
Top Page Image Contents