Murray 425620x92B manual HOW to Replace the Motion Drive Belt, Removal

Page 30

MAINTENANCE

HOW TO REPLACE THE MOTION DRIVE BELT

REMOVAL

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Remove the mid-idler pulley.

3.Disconnect the idler spring (Figure 34).

4.Remove the idler pulley and spacer (Figure 34).

5.Remove the V-idler pulley and spacer.

6.Remove the motion drive belt from the drive pulley (Figure 34).

7.To remove the motion drive belt from the stack pulley, pull the front end of the belt under the stack pulley and then back between the stack pulley and the steering plate (Figure 32).

8.Remove the access panel (Figure 33).

9.Remove the two screws that attach the steering shaft assembly (Figure 33). Raise the steering wheel and steering shaft assembly. Pull the motion drive belt under the steering shaft assembly.

10.Remove the motion drive belt. A correct replacement part or assistance is available from an Authorized Service Center in your area.

INSTALLATION

1.Slide the motion drive belt between the stack pulley and the belt guides (Figure 32). Install the motion drive belt on the top pulley of the stack pulley. Make sure the “V” side of the belt is against the pulley.

2.Push the motion drive belt through the opening between the steering plate and the engine plate.

3.Install the end of the motion drive belt around the drive pulley (Figure 34).

4.Put the motion drive belt around the V-idler pulley. Install the motion drive belt, V-idler pulley and spacer.

5.Put the belt around the idler pulley. Fasten the idler pulley and spacer with the hex nut. Make sure the flat side of the belt is against the idler pulley. Also, make sure the belt is not twisted.

6.Connect the idler spring (Figure 34).

7.Install the mid-idler pulley.

8.Check the routing of the motion drive belt (Figure 34). Make sure the motion drive belt is installed correctly on the idler pulleys and inside all belt guides.

9.Attach the steering shaft assembly to the steering plate with two screws (Figure 33).

10.Attach the access panel (Figure 33).

11.Before you use the unit, check the adjustment of the clutch. See the instructions “How To Check And Adjust The Clutch”.

12.Install the mower housing. See the instructions “How To Install The Mower Housing”.

FRONT

Stack Pulley

Steering

 

 

Plate

Motion

 

Belt Guides

 

 

Drive

 

 

Belt

 

Figure 32

Screw

 

 

Steering Shaft

 

 

Assembly

 

 

Motion Drive

 

 

Belt

Access Panel

Figure 33

 

 

 

 

 

Belt Guide

 

 

 

 

 

Motion Drive Belt

Belt Guide

 

 

 

 

 

 

 

 

Mid-Idler

Pulley

 

 

 

Idler Spring

 

 

 

Idler Pulley

Spacer

 

 

Stack Pulley

Spacer

 

 

 

 

 

 

 

 

 

V-Idler

Pulley

 

 

 

 

 

 

V-Idler

Pulley

 

 

 

 

Drive Pulley

 

 

 

 

 

Idler Spring

 

 

Figure 34

F-040740L

 

30

 

 

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Model Table of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionHOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsHOW to Start the Engine Before Starting the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceFrequency Maintenance Required Comments General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Where to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart 040740L USARepair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Electrical System Light HarnessElectrical System 040740L Index Model No Model No Bushel Capacity

425620x92B specifications

Murray 425620x92B is a notable power tool that has gained attention for its user-friendly design and efficient performance. This model is primarily designed for carpentry and woodworking enthusiasts, making it an excellent choice for both professionals and hobbyists.

One of the main features of the Murray 425620x92B is its robust motor. With a power rating that allows it to handle demanding tasks, this tool provides reliable performance whether you’re cutting, shaping, or smoothing wood. The motor is engineered for longevity, ensuring that users can depend on it for various projects without frequent breakdowns.

The design of the Murray 425620x92B enhances its usability. It includes an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. This is particularly important for users who engage in long hours of work, as comfort can significantly impact efficiency and precision.

In terms of technology, the Murray 425620x92B incorporates advanced safety features. It is equipped with an automatic shut-off function, which activates when the tool overheats. This precautionary measure ensures that users can operate the tool safely, minimizing the risk of accidents. Furthermore, its safety switch prevents accidental start-ups, providing an extra layer of security.

The precision of the Murray 425620x92B is another standout characteristic. With adjustable settings, users can easily modify the depth and speed of cuts according to their needs. This versatility allows for a wide range of applications, from delicate trimming to more aggressive cutting tasks. Additionally, the tool features a dust collection system that helps maintain a clean work environment, reducing cleanup time and enhancing visibility during operation.

Durability is also a hallmark of the Murray 425620x92B. Constructed with high-quality materials, this tool can withstand the rigors of continuous use in various work conditions. Its design includes protective casing that shields internal components from dust and debris, further extending its lifespan.

In conclusion, the Murray 425620x92B is a powerful, versatile, and safe tool ideal for woodworking tasks. Its combination of performance, comfort, safety features, and durability makes it a top choice for those looking to invest in a reliable power tool. Whether you’re a seasoned professional or just starting in the woodworking world, the Murray 425620x92B promises to meet and exceed your expectations.
Top Page Image Contents