Murray 425303x92B manual Attachments, HOW to USE the Throttle Control

Page 15

OPERATION

ATTACHMENTS

This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator.

For all pull–behind attachments or trailers, the maximum gross weight is 250 pounds. Gross weight is the weight of the attachment or trailer and any load that might be on or in it.

Do not operate on a slope that is greater than 10 degrees when using a pull–behind attachment or trailer. We have included a slope guide in this book to help you determine the slope on which you will be operating your unit. Never allow someone to stand or ride on or in an attachment or trailer.

HOW TO USE THE THROTTLE CONTROL

Use the throttle control to increase or decrease the speed of the engine.

CAUTION: Always operate the engine with the throttle control in the FAST position. If the engine runs for several minutes at slower than the FAST position, the engine and transmission will overheat and can be damaged.

1.The FAST position is marked with a detent. For normal opera- tion and when using a grass bagger, move the throttle control to the FAST position. For maximum charging of the battery and for a cooler running engine and transmission, operate the en- gine in the FAST position.

2.For transport and to tow pull behind attachments, control the ground speed with the speed control pedal.

3.The engine governor is set at the factory for maximum perform- ance. Do not adjust the governor to increase the speed of the engine.

HOW TO USE THE BLADE ROTATION CONTROL

The blade rotation control is next to the steering wheel (Figure 6). Use the blade rotation control to engage the blade(s) or to operate a snow thrower attachment.

1.Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position.

2.Move the blade rotation control to the ENGAGE position to rotate the blade(s).

Note: If the engine stops when you engage the blade(s), the seat switch is not activated. Make sure you sit in the middle of the seat. Also, make sure the wire is connected to the seat switch.

3.Move the blade rotation control to the DISENGAGE position to stop the blade(s). Before you leave the operator’s position, make sure the blade(s) has stopped rotating.

4.Before you ride the unit across a sidewalk or a road, move the blade rotation control to the DISENGAGE position.

WARNING: Always keep your hands and feet away from the blade, deflector opening, and the mower housing when the engine runs.

Disengage

Position

Blade Rotation Control

Engage Position

Figure 6

F–030704L

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Check the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlHOW to Drive in Reverse HOW to USE the Speed Control PedalHOW to Drive Forward HOW to Change DirectionsHOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Stop on a Hill HOW to Operate with the Mower HousingHOW to Operate Automatic Drive Units on Hills HOW to Operate on a HillCheck the OIL HOW to Start the EngineBefore Starting the Engine CarburetorMowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchHOW to Remove the Battery HOW to Clean the BatteryHOW to Charge the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Engine Drive Belt Removal HOW to Replace Motion Drive BeltsTo install the engine drive belt, reverse the above steps Engine Drive Belt InstallationTransaxle Drive Belt Removal Transaxle Drive Belt InstallationHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart 030704L MURRAY, INC. Lawn Mower Central Parts DistributorsChassis & Hood Repair PartsKey Description Motion Drive Key Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing 7601032 Repair Parts Engine Mount Engine Mount Repair Parts Electrical System Electrical System 030704L 030704L 030704L Index Mulcher KIT Lawn Sweeper Snow BladeGrass Bagger Mulcher KIT Garden Tiller

425303x92B specifications

The Murray 425303x92B is a high-performance industrial equipment model known for its versatility and reliability in various applications. Designed with precision and engineered to meet the demands of modern industries, this model integrates advanced technologies and features to ensure optimal performance.

One of the standout characteristics of the Murray 425303x92B is its robust construction. Built from high-quality materials, this model can withstand harsh operational environments, making it suitable for use in sectors ranging from manufacturing to construction. Its durability ensures a long lifespan, reducing the need for frequent maintenance and replacements, which ultimately leads to increased operational efficiency.

In terms of technology, the Murray 425303x92B is equipped with an advanced control system that enhances user experience and operational precision. This system allows for real-time monitoring and adjustments, enabling operators to fine-tune performance based on specific operational needs. The user-friendly interface ensures that even less experienced personnel can quickly learn to operate the equipment efficiently.

Power efficiency is another significant feature of the Murray 425303x92B. The model is designed to minimize energy consumption while maximizing output. This not only helps to reduce operational costs but also aligns with contemporary environmental standards, making it an eco-friendly choice for businesses.

Additionally, the equipment is designed with safety in mind. It includes multiple safety features such as emergency stop buttons, overload protection, and fail-safes that help prevent accidents during operation. These features enhance the overall safety of the workplace and provide peace of mind for operators.

The Murray 425303x92B also boasts modular design elements, allowing for easy upgrades and customization. This flexibility means businesses can adapt the equipment to suit changing operational demands without the need for significant reinvestment in new machinery.

Overall, the Murray 425303x92B stands out in the competitive landscape of industrial equipment. With its combination of durability, advanced technology, power efficiency, and safety features, it provides a comprehensive solution for industries looking to enhance their productivity and operational capabilities. Whether used in a manufacturing line or on a construction site, this model is designed to deliver exceptional performance and reliability, making it a valuable asset to any organization.
Top Page Image Contents