Murray 425303x92B Before Starting the Engine, Carburetor, HOW to Start the Engine, Check the OIL

Page 19

OPERATION

BEFORE STARTING THE ENGINE

CHECK THE OIL

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Check the oil. Follow the procedure in the engine manufactur- er’s instructions.

3.If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil.

CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows.

1.Drain the fuel tank.

2.Start the engine. Let the engine run until the fuel lines and the carburetor are empty.

3.After storage, make sure you use fresh fuel. See the storage instructions for additional information.

4.Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur.

ADD GASOLINE

WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclo- sure. Before you add gasoline, stop the engine and let the engine cool for several minutes.

Fill the

fuel tank with regular

Fuel Tank

unleaded gasoline. Do not use

Full

premium

unleaded gasoline.

Make sure the gasoline is fresh

 

and clean. Leaded gasoline will

 

increase

deposits and shorten

 

the life of the valves.

CARBURETOR

The factory settings for the carburetor are for most conditions. If the engine is operated under the following conditions, you can adjust the carburetor mixture. To adjust the carburetor, see the engine manufacturer’s instructions.

1.The engine has a loss of power or does not run smooth.

2.A change from summer to winter operation.

3.A 40 degree change in the operation temperature. The carbure- tor was adjusted at 80 degrees at the factory.

4.The engine is operated above 4,000 feet.

HOW TO START THE ENGINE

WARNING: The electrical system has an operator presence system that includes a sensor switch for the seat. These components tell the electrical system if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat if the blade rotation control is engaged or if the trans- mission is engaged. For your protection, always make sure this system operates correctly.

1. Push the pedal completely forward. Keep your foot on the ped- al.

2.Make sure the blade rotation control is in the DISENGAGE position.

3.Move the throttle control completely forward to the CHOKE or FAST position. Some models have a separate choke knob. Pull the choke knob to the full CHOKE position.

4.Turn the ignition key to the START position. Release the key when the engine starts.

NOTE: If the engine does not start after four or five tries, see the TROUBLE SHOOTING CHART.

5.Slowly move the throttle control to the SLOW position.

6.Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW.

F–030704L

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables Check the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlHOW to Drive in Reverse HOW to USE the Speed Control PedalHOW to Drive Forward HOW to Change DirectionsHOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Stop on a Hill HOW to Operate with the Mower HousingHOW to Operate Automatic Drive Units on Hills HOW to Operate on a HillCheck the OIL HOW to Start the EngineBefore Starting the Engine CarburetorMowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchHOW to Clean the Battery HOW to Remove the BatteryHOW to Charge the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Engine Drive Belt Removal HOW to Replace Motion Drive BeltsTo install the engine drive belt, reverse the above steps Engine Drive Belt InstallationTransaxle Drive Belt Removal Transaxle Drive Belt InstallationHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart 030704L MURRAY, INC. Lawn Mower Central Parts DistributorsChassis & Hood Repair PartsKey Description Motion Drive Key Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing 7601032 Repair Parts Engine Mount Engine Mount Repair Parts Electrical System Electrical System 030704L 030704L 030704L Index Mulcher KIT Lawn Sweeper Snow BladeGrass Bagger Mulcher KIT Garden Tiller

425303x92B specifications

The Murray 425303x92B is a high-performance industrial equipment model known for its versatility and reliability in various applications. Designed with precision and engineered to meet the demands of modern industries, this model integrates advanced technologies and features to ensure optimal performance.

One of the standout characteristics of the Murray 425303x92B is its robust construction. Built from high-quality materials, this model can withstand harsh operational environments, making it suitable for use in sectors ranging from manufacturing to construction. Its durability ensures a long lifespan, reducing the need for frequent maintenance and replacements, which ultimately leads to increased operational efficiency.

In terms of technology, the Murray 425303x92B is equipped with an advanced control system that enhances user experience and operational precision. This system allows for real-time monitoring and adjustments, enabling operators to fine-tune performance based on specific operational needs. The user-friendly interface ensures that even less experienced personnel can quickly learn to operate the equipment efficiently.

Power efficiency is another significant feature of the Murray 425303x92B. The model is designed to minimize energy consumption while maximizing output. This not only helps to reduce operational costs but also aligns with contemporary environmental standards, making it an eco-friendly choice for businesses.

Additionally, the equipment is designed with safety in mind. It includes multiple safety features such as emergency stop buttons, overload protection, and fail-safes that help prevent accidents during operation. These features enhance the overall safety of the workplace and provide peace of mind for operators.

The Murray 425303x92B also boasts modular design elements, allowing for easy upgrades and customization. This flexibility means businesses can adapt the equipment to suit changing operational demands without the need for significant reinvestment in new machinery.

Overall, the Murray 425303x92B stands out in the competitive landscape of industrial equipment. With its combination of durability, advanced technology, power efficiency, and safety features, it provides a comprehensive solution for industries looking to enhance their productivity and operational capabilities. Whether used in a manufacturing line or on a construction site, this model is designed to deliver exceptional performance and reliability, making it a valuable asset to any organization.
Top Page Image Contents